The input voltage X (t), and the output voltage Y (t) of an electrical system are sampled simultaneously at regular intervals with the following results. n = 0, 1 ,2, 3, 4 , 5 ,6 ,7 ,8,9, ... X(nT) = 1, 10 , 6,2, 1, 0,0,0, 0,0,..... Y(nT) = 1, 15, 7.5, -2.75, -2.5 , ---,----> Calculate the missing values of the output voltage Y (nT) above. Hint: Assume that X (t) = zero for t < 0, and that only nonzero impulse response samples are h (n), for 0

The input voltage X (t), and the output voltage Y (t) of an electrical system are sampled simultaneously at regular intervals with the following results. n = 0, 1 ,2, 3, 4 , 5 ,6 ,7 ,8,9, ... X(nT) = 1, 10 , 6,2, 1, 0,0,0, 0,0,..... Y(nT) = 1, 15, 7.5, -2.75, -2.5 , ---,----> Calculate the missing values of the output voltage Y (nT) above. Hint: Assume that X (t) = zero for t < 0, and that only nonzero impulse response samples are h (n), for 0

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Consider a sinusoidal signal x(t)=sin(2n50t) for ten complete cycles. Using this signal, plot to represent the following: (a) Plot x(t) as analog continuous signal (b) Plot x(t) as analog discrete-time signal (c) Quantize the signal to 4 levels, +1, +1/3, -1/3, -1 and plot the corresponding i) digital discrete-time signal; and ii) digital continuous signal (d) Plot the amplitude spectrum for the sinusoidal signal generated in part (a). (e) Plot the phase spectrum for the sinusoidal signal generated in part (a).
A digital signal is defined as x[n] = cos(n4π/5) Is this a digital sequence periodic? Find the first eight elements in the sequence.
Convert the following decimal no.into the binary no. 0,6,11,28,59
INDUSTRIAL ELECTRONICS
A design objective in many control system applications is to achieve small time constants. An exception is the time constant requirements for a piezoelectric sensor. Explain why a large time constant, in the order of 1.0 s, is desirable for a piezoelectric sensor in combination with its signal conditioning system. An equivalent circuit for a piezoelectric accelerometer, which uses a quartz crystal as the sensing element, is shown in the following figure. The generated charge is denoted by q and the output voltage at the end of the accelerometer cable is vo. The piezoelectric sensor capacitance is modeled by C, and the overall capacitance experienced at the sensor output, whose primary contribution is due to cable capacitance, is denoted by Cc. The resistance of the electric insulation in the accelerometer is denoted by R. Write a differential equation relating v, to q. What is the corresponding transfer function? Using this result, show that the accuracy of the accelerometer improves…
Electrical Engineering (a) Some polycrystalline photovoltaic cells are to be arranged to provide an output of 12V and a power of 120W. Design and sketch out the cell configuration that meets the specification, using a sketch. The datasheet shows that open-circuit voltage is 0.622V, short-circuit current is 8.XY A, and fill factor is 0.7Z. X=3 Y=2 Z=2
Suppose that "is in lowest terms and that m < n. Then " has a simple-periodic dec- imal representation if and only if 2 or 5 are not factors of n.
Use the Fermi-Dirac equation to determine the probability that an allowed energy state is occupied by an electron if the state is 0.03 eV below the Fermi level and T = 500K. OP = 76.1% OP = 81.0% OP = 66.7% OP = 70.5%
HW 1)find the oufputof the Sxstena hcn)=2ucn-1) iR its input xcn) =()"u() %3D
Draw the waveform corresponding to to a BASK signal whose sequence is: 1 0 1 1 0
Given: Vin = Vpeak sin(w)(t) Vpeak = 5V R1 = 1k ohms And using the ideal diode model What is the Vo waveform for 2 periods. Calculate for the average Vo and derive a formula for Vo in terms of Vpeak .
Q.15: The switch has been in position "a" for a long time. At t=0 the switch is moved to position "b". Use classical method to find the voltage across and current through the capacitor as a function of time? (Ans.: Vc(t)=80[1.25-e 20 b1002 10m H t%3D0S 30V 42 100V 2uF 5000t -5000t (cos5000t+sin5000t)] V & ic(t)=1.6e sin5000t A)