If the input voltage for the given circuit below is 220 V at 50 Hz, the load resistance (RL) is 4700 and theaverage output voltage is 25 V. Assume the diodes to be silicon diodes. Determine the turns ratio of thetransformer used.If a capacitor of 120 µF is connected parallel to the load resistor (RL), Determine the ripple factor.D3D1VD2a. The turns ratio of transformer (Npri/Nsec) isb. The Ripple factor isllleell

the input voltage for the given circuit below is 220 V at 50 Hz, the load resistance (RL) is 4702 and t verage output voltage is 25 V. Assume the diodes to be silicon diodes. Determine the turns ratio of tl ransformer used. a capacitor of 120 µF is connected parallel to the load resistor (RL), Determine the ripple factor. D3 D1 ill

the input voltage for the given circuit below is 220 V at 50 Hz, the load resistance (RL) is 4702 and t verage output voltage is 25 V. Assume the diodes to be silicon diodes. Determine the turns ratio of tl ransformer used. a capacitor of 120 µF is connected parallel to the load resistor (RL), Determine the ripple factor. D3 D1 ill

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the Total Current of the Circuit during the negative half cycle in milliamps. Consider the Diodes as a Silicon Zener Diode. v2 D1 V3 D2 2 2 2 V1 Vout AC R1 12 1k
For the given circuit assume that the diode is ideal and the discharging time constant is much greater than the time period of the input signal. The output waveform will vary between. a. -2V to -12V b. -2V to -22V c. 2V to 12V d. 8V to -12V (SHOW COMPLETE SOLUTION AND EXPLANATION)
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consisting series connected a resistor and an inductance from a 70.7V (RMS), 50HZ sinusoidal AC source. The firing delay of the thyristor is 90° and the load values are R=102, L=0.1 H. Define the load current expression and draw the load current by calculating for first two periods. And calculate the average values of the load voltage and current.
A silicon diode with a forward resistance of 100 is connected in series with a 5000 resistor. If an a.c voltage of 20V peak is connected across the series combination of the diode and the resistor what will be the peak value of the current through the diode and the peak output voltage? What will be the peak value of the current through the diode and the peak output voltage if the diode were ideal?
Consider a junction diode has dc biased current at operating point ID=0.8 mA. A sinusoidal voltage is superimposed on the VD such that the peak-to-peak sinusoidal current id(t) = 0.05ID. Find the value of the applied peak-to-peak sinusoidal voltage vd(t).
Q3) For the circuit shown in figure (2), assume the diode is ideal, answer the following: 1) Draw the output voltage then find the de output voltage. 2) If a capacitor 100uF is connected across RL load, Draw the output voltage then find de output voltage and Ripple Factor. 18:1 Vin 220V SOHz
Diodes would be considered ideal. Which of the following is true? 1. The DI diode is in the plug. II. The DI diode is conducting. I. Diode D2 is conducting. IV. Diode D2 is in the plug.
Draw output waveform for the following circuit. Suppose input is a pure square wave with a positive half at 10 V and negative half at -10 V for ideal diodes. D1 D2 220 R3 R1 1k R2 1k
Given the following circuit with VDD = 9.5 V, R = 3.2 k2, then the current Iis: Use the CVD model for the diode, with VD = 0.65 V. VDD I a. 0 A O b. 0.002766 A c. 0.002969 A d. 2.968750 A e. 2.765625 A R N V₂
In the circuit below, sinusoidal input voltage with a peak value of 10V is applied. Calculate the current flowing through the diodes D1 and D2 by drawing the waveform of the output voltage. (Both diodes will be considered ideal and Vc=5V).
as soon as possible please
These are subparts of a question so please answer all and dont palagarize