The input to the circuit shown in Figure P 3.6-44 isthe voltage of the voltage source, 32 V. The output is thecurrent in the 10- resistor io. Determine the values ofthe resistance R₁ and of the gain of the dependentsource G that cause both the value of voltage across the12 Ω to be Va = 10.38 V and the value of the output currentto be i, = 0.4151 A.R₁OUTHEN. A E LO32 V 12 QGua40 Ω 10 22.ioFigure P 3.6-44Va

Answered: Image /qna-images/answer/40268044-a6c1-4381-8633-27098ed88e50.jpg

The input to the circuit shown in Figure P 3.6-44 i the voltage of the voltage source, 32 V. The output is th current in the 10-2 resistor io. Determine the values o the resistance R₁ and of the gain of the dependen source G that cause both the value of voltage across th 12 2 to be va = 10.38 V and the value of the output currer to be io = 0.4151 A. ww R₁ 32V 12Ω Va Figure P 3.6-44 + - Gua www 40 92 10 Q2 ܘܐ

The input to the circuit shown in Figure P 3.6-44 i the voltage of the voltage source, 32 V. The output is th current in the 10-2 resistor io. Determine the values o the resistance R₁ and of the gain of the dependen source G that cause both the value of voltage across th 12 2 to be va = 10.38 V and the value of the output currer to be io = 0.4151 A. ww R₁ 32V 12Ω Va Figure P 3.6-44 + - Gua www 40 92 10 Q2 ܘܐ

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

basic electronis please give full answer thanks Given Sketch the drain and transconductance curve for VGS = +2V, +1V, 0V -1V, -2V, -3V and -4V.
Q#3(a) Find the output voltage and voltage drop across RS and current through Zener diode Rs = Two digit of Your roll number Ω and RL =10 k Ωshow in figure #2 roll no 52
Calculete I1, I2 and I3 currents for an ideal opamp in the circuit given in the figure.
In the circuit below, when a 2.2KN load is connected to the output, find the value of the current flowing through the R resistor (IR), the current passing through the zener diode (Iz) and the load current value (IL). Sigorta T1 Dr-De 1N4001 0,1A REGOLATOR D 220V AC Va-20V Vs AC Va 2200 De Vi-13V 15V 4700uF IN47448 Nominal Test Maximum Dynamic Impedance Maximum Reverse Zener Current Leakage Current Voltage) Vz @ IzT IZT ZT @ IzT ZZK @ IzK IZK IR Test Voltage VR V mA Ω Ω mA µA V 15 17 14 700 0.25 11.4 llle
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A
Draw a full-wave bridge rectifier circuit (use multisim) connected to a load resistance of 470 N, with input VPP= 29 V. Connect a voltmeter across the load and an ammeter to measure the current through the load. Peak voltage of the output from the graph Average voltage across the load from the voltmeter reading Average current from the ammeter reading Insert the picture of the simulation here
For circuit given in Figure 3 use Complete Diode Model andfind the voltage across R1 and R2 andtotal current flowing in this circuit. Giventhat diodeforward resistance is 15 Ohmsfor D1 and 10 Ohmsfor D2, also reverse current flowing acrossD2 is 20 micro Amperes. DI Ri 50 Q ww D2 Rz100 N KH 10 V R3150 2 www Figure 3
If Vz-8 V and Pzmax=150mW. Determine the minimum value of RL to ensure the Zener diode is in the ON state 14 118 Ohm 210 Ohm 235 Ohm 105 Ohm 470 0 33°C Activate Windo Go to Settings to ac c's
Could you please help me in this question?
Consider a PV Module with 4 solar PV cells with the Size of each 10cm x 10cm are connected in Parallel. If we connect a lamp load of 2W across this module, choose the correct statement for the above PV Module. (Assume necessary data) a. The output voltage is 0.5V, the output current is 2A b. The output voltage is 0.5V, the output current is 4A c. The output voltage is 2V, the output current is 2A d. The output voltage is 2V, the output current is 4A
urgent please
Consider a pn junction in forward-bias at room temperature. To obtain a current of 1mA with a voltage of 750 mV, Calculate Is. V = 26 mV. Select one: O a. 2.97 x 1018 A O b. None of these Oc. 2.97 x 10-16 A O d. 2.97 x 10-17 A