The initially stationary 11-kg block is subjected to the time-varying horizontal force whose magnitude P is shown in the plot. Note that the force is zero for all times greater than 8 s. Determine the time t, at which the block comes to rest. H=0.47] H₂ = 0.68 11 kg P, N 97 8 t, s

Q: Convert 3 centimetres (cm) to millimetres (mm)

A: Given data: Unit = 3 centimetre Need to convert into millimetre.

Q: 3. During tug of war, the bicep muscle generated 4k N force that was perpendicular to the forearm…

A:

Q: The specific energy curve is shown below. Matching questions with correct answers. Уз 1 Y₂ Fluid…

A:

Q: Please give a detailed handwritten solution. Use the correct formula. Don't use chatgpt.

A: ( If you have any questions related to this problem please feel free to ask me).

Q: Convert each temperature. 22 °C to K (approximate room temperature)

A: Given, temperature = 22oC we know 1oC = 273 K

Q: Which of the following statement is correct O 1. Reynolds number depends on the viscosity of fluid O…

A:

Q: The pressure of oil in the pipe (in kPa)

A:

Q: What is the pressure at 61, 500 ft in SI.

A:

Q: The coal consumption per hour is the ratio of heat of combustion and calorific value.

A: True

Q: 6. From among the following, the largest increment of pressure is A. 1 Pa B1 psi C. 1 in H₂O D. 1 in…

A:

Q: A hydro-electric dam uses turbines to generate electricity as reservoir over the turbine blades. A…

A: (a) To fill: The blanks of the statement with appropriate choice. Explanation: Hydroelectric dam: A…

Q: 6-The (Pitot Tube) it is used to measure the speed of the air and gases in various industrial…

A: This question is based on the concept of pitot tube from fluid mechanics.

Q: In the compressor, the exit area should be smaller than the inlet area due to increasing the liquid…

A: A compressor is a device that increases the pressure of a working fluid by reducing the volume of…

Q: A power plant turbine releases its discharge into a condenser operating at 20C at 100% saturated…

A: It is given that:condenser temperature is 20°C. Steam enters condenser as 100% saturated vapor.Mass…

Q: b) Name the type of this system c) Name the device and specify what type of pressure measured d)…

A: given; define the name of the system;

Q: The weight of 7.7 litre water is equal to 1274.026

A: The Quantity  of the water is given as, Q=7.7 L

Q: Where can i get the values: x2=0.92 and v2 = 13.5079

A:

Q: What are the units of F in the equation below: F = mg/gc where m is mass in lbm; g is acceleration…

A: Given;m is the mass in lbm (pounds mass).g is the acceleration due to gravity, which is given as…

Q: The pressure at point 1 is 200 kPa. Find the pressure in point 2 (answer in kPa, 2 decimal places)…

A:

Q: In a steady flow through a nozzle, the flow velocity on the nozzle axis is given by v-uo (1+3x/L)i…

A:

Q: 1 kN/m 1m

A: Shear force is an internal force in any material which is usually caused by any external force…

Q: Given: Diameter of pipe in point 1 = 3.2 Diameter of pipe in point 2 = 2.3 Specific gravity of the…

A: since the units of pressure are not provided, assuming the unit to be ft of water Velocity at…

Q: What is called to "USE OF TEMPERATURE INTERVAL OR DIFFERENCE EQUAL TO THE KELVIN

A: The link between the Celsius and Kelvin scales can be expressed mathematically as follows: K = 273 +…

Q: A pressure vessel contains a gas at 1200 psi. Express the pressure in pascals,

A: GIVEN = PRESSURE IS GIVEN IN PSI [POUND PER SQUARE INCH ] THAT IS 1200 PSI TO FIND =PRESSURE IN…

Q: 3. A pump discharges 126 liters per second of brine (sp.gr.1.20). The pump inlet, 304.8 mm diameter,…

A: Given: The volume flow rate of brine, Q = 126 liters/s = 0.126 m^3/s The specific gravity of brine,…

Q: this quickly

A:

Q: A15 A16 A17 A loss of head due to sudden contraction is known as minor head loss. TRUE The pressure…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: 5.8 bar pressure is equivalent to mm of mercury. O a. 4347.30 O b.42647.06 OC.4547949.50 O d. 4.35

A:

Q: The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32 mm…

A: Find  Mean effective pressure, Indicated Power

Q: Which of the following statements are correct? Select all that apply.

A: A hurricane is a monster of a storm! Strong winds spiral inward and upward at speeds of 75 to 200…

Q: 1. Determine the pressure difference between the water pipe and the oil pipe. S = 0.68 20 cm Oil (s…

A:

Q: y are there so many different units for measuring pre

A: For the sake of convenience, several units are used to represent the wide range of pressures that…

Q: Fluid viscosity is the proportionality constant between the shear force and the change of fluid…

A: True

Q: Q1: Answer by True or False. 1- The pressure diagram can be used to calculate the hydrostatic force…

A: We are suppose to solve only 3 subparts. Please post other question as a separate question.

Q: Which of the following statement is correct   1. Reynolds number depends on the viscosity of fluid…

A: Option 1 is correct.

Q: Perform unit conversion. 1432 cm^3 to L

A:

Q: Diogrum height, cm The bore diameter of each cylinder in a six-cylinder four-stroke petrol engine is…

A: Given  No of cylinder K=6 4 stroke engine,

Q: Which of the following is/are not true? i. Specific gravity is sometimes termed as relative density.…

A: It is required to choose correct answer

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.