The horizontal force P is applied to the cable wrapped around the inner spindle of the spool. The spool of cable weighs 20.37 lb/ft2, per unit of cross-sectional area that is visible, which accounts for the width into the page. The static friction between the spool and the 15° incline is ?s = 0.40. Determine the friction force acting on the spool if P is just sufficient to roll the spool up the incline without sliding. 15° 30" 18" P

The horizontal force P is applied to the cable wrapped around the inner spindle of the spool. The spool of cable weighs 20.37 lb/ft2, per unit of cross-sectional area that is visible, which accounts for the width into the page. The static friction between the spool and the 15° incline is ?s = 0.40. Determine the friction force acting on the spool if P is just sufficient to roll the spool up the incline without sliding. 15° 30" 18" P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cable carrying traffic signal loads is shown in the figure. The deflection at point B is 12 in. Neglect elongation of the cable. The tension force (lb) in the cable between C and D is most nearly: (A) 4,685 (B) 4,476 (C) 1,816 (D) 213 ← A 40 ft +++-12A-+-16A | B с 200 lb 125 lb
A cable is attached to a 2.1 kg block A. Block A is looped over a fixed peg at C and is attached to plate B. The coefficient of static friction between the plate and the block is μa=0.30. The coefficient of static friction between the plate and the inclined plane is μb=0.35 and the coefficient of static friction between the cable and the peg is μc=0.41. If the plane’s angle is 30 degrees, what is the maximum mass that plate B can have such that it does not slide down the plane and remains stationary?
Final answer in 3 decimals
Can you please answer these two questions?
Problem 3 From the figure below determine the following. a. Determine the tension in the cable at mid length where the slope is zero. b. Determine the maximum force in the cable 51.6 25.8 25.8 JA B 4 m 2 m 6 m D Pin 5.6 142.4
Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable CD is required for static equilibrium in the position shown? What is the tension T in cable CD? T 3.3' Answers: LCD = TCD= i A 46° B 46 lb ft. lb D
Determine the tension P in the cable which will give the 107-lb block a steady acceleration of 4.4 ft/sec2 up the incline. 39° 107 Ib Hi -0.40 36° Part 1 Write the equations of motion in the x- and y-directions. 4.4 ft/sec? 107 lb 39° 36° Answers: EF, : FN + P+ i Ib = ( i i EFy : FN+ i P+ i Ib = 0 i
A winch at point B is used to slide a box up a chute CD in a warehouse. If the component of the force from cable AB in the direction of the chute must be 410 lb, determine the force in the cable for the position of the box given below. The chute is parallel to the xz 1 the distance up the chute plane. Neglect the size of the box and the winch. The box is from point C. 105in. Z B (-45, 0, 130) in. 135in. 40 in y FAB = lb
Given: The structure shown below is cantilevered at the Point A and welded at point B. In addition, the magnitude of the tensile force in cable GE is 2,000 N, and member BC is parallel to the x axis. y 6 т G В cable 6 m 6 т 15 m 10 m 40 KN Required: a) Determine the vector components of the force in cable GE. b) Draw a free body diagram of the orange structure. c) Determine the components of the reactions at point A.