The horizontal cross-section of the cast-iron standard of a vertical drilling machine has the form shown. The line of thrust of the drill passes through P. Find the greatest value the thrust may have without the tensile stress exceeding 15 MN/m2. What will be the stress along the face AB? (Cambridge) ANSWER: 17.68 kN; 11.8 MN/m2 compressive.

Q: pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE…

A:

Q: Pa. Construct the Mohr's circles

A: The stress state at a point of a machine element is give by.

Q: Determine the stress components at point H. And show the stress state for this point on a volume…

A: Show the force and moments on cross section H.

Q: 100 kip 10 kip-ft The 4-in. diameter shaft shown above is made from a ductile brass alloy. Which of…

A: solution Given d=4 in

Q: Q) In Fig.(1), the shaft is subjected to a reversed load P (2700 to -900) N. Find the length (L), if…

A:

Q: find the bearing stress between bolts and plate 10/-.. 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN…

A: Given data  diameter of bolt (d) = 10 mm thickness of plate (t) = 8 mm  Load acting on the plate…

Q: Determine the torsion on the rigid supports and the maximum shearing stress developed in each…

A:

Q: Problem 1: If the parts of the shaft below are a 1" diameter solid steel rod and a 2" OD diameter…

A:

Q: Determine the size of the shaft,

A: Given: P=22 kW N=550 rpm shear stress=42 MPa Tensile/compressive stress=56 MPa P=900 N L=2.5 m To…

Q: 3. (a) Using Stress transformation equations, determine the principal planes, the principal stresse…

A: To find: The principle planes, the principle stress, the maximum in-plane shear stress and the…

Q: For the given state of stress, determine the planes with compressive normal stress equal to 15 MPa.…

A:

Q: A cantilevered solid shaft with length of 400-mm and diameter of 150-mm is loaded at its free end as…

A:

Q: Find the minimum diameter required of the circular steel shaft shown below if the largest shear…

A: Given, The length of the shaft is = 1.5 m Maximum allowable shear stress = 200 MPa Net torque is=…

Q: A sleeve made of AISI 1040 CD steel has inner and outer diameters 40mm and 50mm, respectively. press…

A:

Q: On section a-a, determine the stress state at points A & B. Neglect the weight of the block. If the…

A: Find:stress state at point A and B

Q: The 0.91-in.-diameter rod in (Figure 1) is subjected to the loads shown. Figure 9 in. 200 lb 300 lb…

A:

Q: The state of stress at a point in a member is shown on the element below. If: 0x = 9 MPa Oy=-14 MPa…

A:

Q: ure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined…

A:

Q: In the figure shown below, set P = 48 lb, D1 = 8 in, D2 = 4 in, D3 = 4 in, and the bit diameter to…

A:

Q: How is the state of plane stress at the point uniquely represented?

A: If the stress state at a material particle is such that the only non-zero stress components act in…

Q: A machine part is subjected to an axial loading situation where Fmin = 3700 lbf and Fmax = 12000…

A: Given:Maximum axial force, Fmax=12000 lbfMinimum axial force, Fmin=3700 lbfCross-sectional area,…

Q: The built-up shaft consists of a pipe AB and solid rod BC. The pipe has an inner diameter of 18 mm…

A: Part A) The outer diameter of the tube is do = 24 mm = 0.024 mThe inner diameter of the tube is di =…

Q: What is the maximum in-plane shear stress for the given state of stress? Express your answer with…

A:

Q: Mohr's Circle Please answer the following with a complete solution so that i can understand how to…

A: Given:σ1=5000 psfσ2=-2000 psf

Q: 2 A hollow steel tube with an inside diameter of 110 mm must carry a tensile load of 480 kN.…

A:

Q: The 6 kN force is in the vertical direction, while the P=7.5 kN force is in the z direction.Since…

A:

Q: A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a…

A:

Q: A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a…

A:

Q: Part A. if the bolt is subjected to a compressive force of P= 21.3 kN, deteemine the magnitude of…

A: Write the given values along with suitable variables.

Q: The 4-In. diameter shaft shown above is made from a ductile brass alloy. Which of the following are…

A: Normal Stress = Force / Cross Section Area = 4*100 / (π 4^2) = 7.957747154 Ksi Shear force is to be…

Q: se 32 in2 and 48 in2 cross-sectional areas for tensile and compressive members, respectively.…

A: Given data given truss system

Q: The composite bar consists of a 22-mm-diameter A-36 steel segment AB and 54-mm-diameter red brass…

A:

Q: Torsion. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which…

A: Given data: ◆ The bolt circle diameter: D = 250 mm ◆ The number of bolts: n = 12 bolts ◆ The…

Q: For the given machine part, where the cross-sectional area at m-n is a square with side 5 mm,…

A: The largest allowable value of the distance: e = 11.6667 mm.

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.