The homogeneous cylinder of mass m and radius Ris placed on the cart and restrained by a horizontal cord. The staticcoefficient of friction between the cylinder and the cart is us. Determine thelargest acceleration, amax, Oof the cart for which the cylinder does not slide.Express amax in terms of g and us.CordRma

Answered: Image /qna-images/answer/8871e361-3ba3-40ca-ab9a-40f4f05a4793.jpg

The homogeneous cylinder of mass m and radius R is placed on the cart and restrained by a horizontal cord. The static coefficient of friction between the cylinder and the cart is µs. Determine the largest acceleration, amax, of the cart for which the cylinder does not slide. Express amax in terms of g and µs. Cord R m a

The homogeneous cylinder of mass m and radius R is placed on the cart and restrained by a horizontal cord. The static coefficient of friction between the cylinder and the cart is µs. Determine the largest acceleration, amax, of the cart for which the cylinder does not slide. Express amax in terms of g and µs. Cord R m a

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q4. The ( 25 kg ) block is moving down the incline surface with an acceleration of ( a = 6 m/ sec"). Determine the coefficient of kinetic friction of the surface ( u ). 25kg Mk? 35°
3/71 The small object is placed on the inner surface of the conical dish at the radius shown. If the coefficient of static friction between the object and the conical sur- face is 0.30, for what range of angular velocities w about the vertical axis will the block remain on the dish without slipping? Assume that speed changes are made slowly so that any angular acceleration may be neglected. Ans. 3.41
The 29-kg spool of outer radius ro=530 mm has a centroidal radius of gyration k=355 mm and a central shaft of radius ri=215 mm. The spool is at rest on the incline when a tension T=204 N is applied to the end of a cable which is wrapped securely around the central shaft as shown. Determine the acceleration aaa of the spool center GGG and the friction force FFF acting at the interface of the spool and incline. The friction coefficients there are μs=0.28 and μk=0.17. The tension T is applied parallel to the incline and the angle θ=16. The acceleration aaa and the force F are both positive if up the incline, negative if down.
The system shown below consists of a uniform disk D that has a mass of mp = 3.0 kg and a radius of r = 1.0 meters. The disk is connected by a massless cable to a block. The system is released from rest and the disk starts rolling without sliding with the angular acceleration of a = rad 30 s2 in the clockwise direction. Determine the magnitude of the friction force (in Newtons) developed between the disk and the inclined surface at this instant. Consider 0 = 40° and g = 10 m. mp
- Determine the acceleration of the system. - Determine the magnitude of the force that each crate exerts on the other.
An occupied cable car with a mass of 360 kg runs along the fixed overhead cable and is controlled by the attached cable at A with a tension of T = 1.8 kN. Force Pexerted on the wheel assembly by the cable. find the acceleration the cable car. wheel assembly O a. 0.45 ms 2 O b. 0.49 ms ² O c. 0.56 ms-² d. 0.53 ms 2 5 11 T GO W T
determine acceleration and tension
The spring-mounted 0.82-kg collar A oscillates along the horizontal rod, which is rotating at the constant angular rate À = 9.1 rad/s. At a certain instant, r is increasing at the rate of 850 mm/s. If the coefficient of kinetic friction between the collar and the rod is 0.56, calculate the friction force F exerted by the rod on the collar at this instant. Vertical 0 Answer: F= i Attempts: 0 of 3 used Submit Answer eTextbook and Media Save for Later N
The man pushes on the roller with force P through a handle that connects to the central axle of the roller. If the coefficient of static friction between the 43-lb roller and the floor is ls = 0.12, and the force Pis maximum so that the roller is about to slip, determine the angular acceleration of the roller (in rad/s²). Assume the roller to be a uniform cylinder. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper unit. Take g = 32.2 ft/s2. 1.5 ft 30° Your Answer: Answer
The block shown has a mass of 51kg and is acted upon by a horizontal force P. The coefficient of friction is 0.40 between the body and the incline. Calculate the magnitude P required (a) barely to prevent the block from slipping down the incline, (b) to give the block an acceleration of 2.4 m/s2 up the incline.
the cylinder with a mass m1=2kg and radius r=0,1m is placed at a plate with mass m2=4kg. We are applying force F at this plate. Find an acceleration of the plate, when the friction coefficient μ=0,2
3/72 The small object is placed on the inner surface of the conical dish at the radius shown. If the coefficient of static friction between the object and the conical sur- face is 0.30, for what range of angular velocities w about the vertical axis will the block remain on the dish without slipping? Assume that speed changes are made slowly so that any angular acceleration may be neglected. (0 0.2 m m 30° CamScanner Lino izowall