The graph shows the speed-torque curves of a stepper motor. Nom 16 14 12 10 . 6 4 456810² 3456810 456810 a. If a pulse rate of 300Hz is provided to the motor which is initially at rest, what is the range of torque values that can be accepted by the motor such that there is no slippage b. Explain why is slippage undesirable for a stepper motor. c. At no load, the motor spins at a maximum of 3000 rpm. What is the step angle of the motor

The graph shows the speed-torque curves of a stepper motor. Nom 16 14 12 10 . 6 4 456810² 3456810 456810 a. If a pulse rate of 300Hz is provided to the motor which is initially at rest, what is the range of torque values that can be accepted by the motor such that there is no slippage b. Explain why is slippage undesirable for a stepper motor. c. At no load, the motor spins at a maximum of 3000 rpm. What is the step angle of the motor

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 4 pole, 300 V Series Wound DC Motor developing 25 HP and 81.57 N-m torque runs at a speed of 750 RPM when the current is 65 Amp.. a) Assuming that the Flux varies directly with the current, calculate the Torque if the load increases so that the Motor takes 75 Amp. b) Calculate the terminal voltage required so that the Motor will developed the same Torque of 81.57 N-m when the speed will be 960 RPM. Please draw the cicuit diagram
A A permanent magnet DC motor has an armature resistance supplied by a 75-V DC Source, 1.4 S2. When it n svy t no-load speed d 2200 pm and draws 1.7 A. a) what 6.) What is the rotational'loss ? TS the output power (in hp) when it is operated at from 1800 rpm a 70-V DC source 7
A 220V shunt motor develops a torque of 108 N.m at an armature current of 20 A. The torque developed when the armature current is 40 A is
I need the answer as soon as possible
A dc shunt motor developes 10 HP at 8000 rpm when drawing a line current of 40 A at 220 V. Find the efficiency at this load and the useful torque.
A220 Vshunt DC motor rotates with speed of1800rev/min.( need handwritten only ,otherwise downvote.)
I need the answer as soon as possible
Please answer alll subparts in short for like either dislike
The supply voltage to a DC motor is 160V. If the back emf Ez=155V and the armature resistance A6 is 0.250, the armature current is a) 5A b) 10A c) 15A d) 20A 1800 ro/min The frequency
both parts fast plz don't answer 3.00 pm
a 220 V dc shunt motor has armature resistance 0.23 ohm, on load it takes armature current 40 A and turnes at 720 rpm, if the flux of motor is reduced by 10% without changing the load torque . Find the new speed of the motor.
Q1. (A)- A series DC motor runs at 600 r.p.m drawing a current of 52A when connected to 220 V supply. The total resistance of the machine is 0.14 2. Calculate the value of the external resistance to be connected in series with the motor circuit to reduce its speed to 400 r.p.m. Assume the load torque is decreased to half of the previous value. Consider the field flux is proportional to armature current.