The graduated cylinder was found to an average of 9.765+ or -0.170 mL in measuring 10 mL portions what are the percent error and percent accuracy of the graduated cylinder
Q: Suppose that in measuring the length,width, and height of a box, there is a maximum 1% error ineach…
A: Given: The error in length of the box is dll=1%. The error in breadth of the box is dbb=1%. The…
Q: When calculating percent error are you supposed to round the true value to match your estimated…
A:
Q: The adjocent figure ahowa the scales of a micrometer. If the vertical scale has 50 divisiona ond the…
A:
Q: Find the precision of the 4th measurement, from the values in the table below No Xn 1 48 2 50 3 52 4…
A: The accurate measurement will be the average value Xnavg = (48+50+52+47+51)/5 = 49.6
Q: Four research teams measured the length of a rare whale, and what each team wrote in its team…
A: Accurate measurement: The closeness of measured value with a standard value or true value is called…
Q: What is the cost per mile to drive a van that has a gas mileage of 12.7 miles per gallon and the…
A: From the question it is given that Distance covered = 1 mileMileage of van = 12.7 miles per…
Q: Is the formula dimensionally correct a =Ft/m
A:
Q: MEASURED USING CENTIMETER RULER MEASURED USING CENTIMETER RULER Measured Diameter d (cm) Measured…
A: Solution: Calculate the relative uncertainty in diameter for dime. ∆Uddime=0.051.76×100=2.84%…
Q: A member in your group writes a length measurement as 2.26 ± 0.2 . The first term, 2.26, is called…
A:
Q: In the figure shown below the ratio "sin 03/sin 0," 03 02
A:
Q: find the weighted mean of the angle.
A: Weighted mean is calculated as Xw=∑iwx∑iw where w is weighted value and x is variable.
Q: You repeated a measurement 6 times and recorded the time using a stop watch: 5.6s, 4.6s, 4.8s, 5.1s,…
A:
Q: Read the measurement on the Vernier calliper below and determine the absolute error, relative error…
A: Absolute error = Measured value - true value Relative error = Absolute error / true value Percentage…
Q: What is “Random and Systematic Error”? Give an example for each one. What is “Standard deviation”…
A: Disclaimer: “Since you have asked multiple question, we will solve the first question for you. If…
Q: What are Personal Errors? How shall this affect the final measurements? How Shall we minimize these…
A: SOlution: To describe about personal errors and thier effect on the measurement.
Q: Max and min that would round to 8.6 oz? What is the uncertainty in the measurement?
A: Given :- weight = 8.6 oz
Q: What is the percent uncertainty in the measurement 3.99±0.35m?
A: Given that, Measurement: 3.99±0.35m
Q: The table shows the set of five measurements recorded in a laboratory. The precision of 2nd…
A: The formula for finding the mean of the given measurement is given by, Here, Σx and n represents…
Q: Round off the answer to the same number of significant digits as are in the measurement with the…
A: We are given 2 physical quantities. First is dimension of mass. Other is dimension of volume. We…
Q: The mass of an aluminum cube was measured to be (A)=71.2 g. Using the Vernier caliper, the length of…
A:
Q: If you are to measure the length, width and thickness of a book, what measuring device will you use?…
A: According to question: For measuring the length, width and thickness of a book, I prefer Measuring…
Q: Rewrite the following measurement in terms of its absolute error: 47 N±6% Select one: (47 ±6) N…
A:
Q: Relate accuracy, trueness, and precision with standard deviation and variance. Explain not more than…
A: Accuracy :- Accuracy refers as the closeness between experimental and…
Q: A. QUANTITATIVE ANALYSIS: Write A if what is in column A is greater than in column B, B if column A…
A: Since you have been posted multiple questions. SO we are solving only first question for you. If you…
Q: It is observed that a height of child is growing 0.5 inch per 6 months. At the age of 6 years, if…
A: Here given that the height of a child grows 0.5 inch per 6 month.Again at the year of 6 the height…
Q: Here's the aluminum (Al) cylinder: 1 4 Here's the lead (Pb) cylinder: 3. 1. What is your estimate…
A: To determine: Length, volume, density and their uncertainties.
Q: Suppose we measure the length of a table to be Xa= 59.7 inches,but the true value is Xa = 59.5…
A:
Q: According to measured values given in following table a) Calculate the value of the Rx for each…
A: a We know. Rx=R2R1=L2L1 1 R1=15000 Ω and R2=Rx=4700 Ω L1=755 mm and L2=1000-755 mm. Therefore,…
Q: First
A: Given: Image of screw gauge and Vernier Calipers.
Q: Consider the figure below, where you make a measurement of object's length using the ruler provided.…
A: In physical world nothing can be measured with 100% accuracy. There will always be error present in…
Q: You also measure the length of a side of the cube using a ruler and get the value 3.15+0.05 cm.…
A: We need to calculate volume with proper error uncertainty value.
Q: Measured values are usually presented as mean plus or minus uncertainty. If two experimental values…
A: Given Two experimental valuesare (8.1 ± 0.5) and (7.9 ± 0.4) To find out The uncertainty of their…
Q: UNCERTAINTIES IN MEASUREMENT: 1.the dimensions of a metal cylinder were measured three times and…
A: Given, Height of the metal cylinder h1=5.50cmh2=5.48cmh3=5.48cm Diameter of the metal cylinder…
Q: (4) A group of students measured the ratio of circumference to diameter to be 3.34. The reference…
A: Given:Student obtained the ratio of circumference and the diameter of the circle = 3.34Reference…
Q: A digital micrometer measures the diameter of two cylinders. Cylinder 1 diameter = 15.22 ± 0.02 mm…
A: Uncertainty in difference or addition is given by direct addition of uncertainty in given…
Trending now
This is a popular solution!
Step by step
Solved in 2 steps