The given girder has beams framing into it at the ends and at every L/3 point. The beam carries a service live load of 20 kips as shown and superimposed uniformly distributed service dead load of 10 kip/ft. Select the lightest A992 W-section that can carry the load. Do not check for deflection. = 20 kips P, LL W. DL = 20 ft L PLL = 10 kip/ft WDL L/3 BEAMS FRAMING INTO GIRDER L

The given girder has beams framing into it at the ends and at every L/3 point. The beam carries a service live load of 20 kips as shown and superimposed uniformly distributed service dead load of 10 kip/ft. Select the lightest A992 W-section that can carry the load. Do not check for deflection. = 20 kips P, LL W. DL = 20 ft L PLL = 10 kip/ft WDL L/3 BEAMS FRAMING INTO GIRDER L

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam shown pind IL. Por RA dueto uniferm load (sENim) and concentrated load (lokn) only positive RA J 2m Im, Lm, 1m IL RA
Verify the adequacy of column AB, part of a sway frame structure, to carry the loads shown in the figure. The column is made of ASTM A36 steel (Fy = 250 MPa). Use ASD specifications. For determining its effective length factor, neglect inelastic effect. %3D W21X62 C W21X62 L=5 m L=5 m Flanges of Columns and web of girders are in the plane of the frame NOTE: Take note of the moment of inertia to be used (ly) for columns. W18X50 W18X50 L=5 m L=5 m P(DL) = 40 kN NM 001 = (10)d NM 00S = (1)d NY SZI = (1)d W21X62 L-4.2m W21X62 L=4.2 m
Current Attempt in Progress A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal before the load Pis applied. Bars (1) and (2) are both made from steel (E - 30600 ksi) and both have a cross-sectional area of 0.87 in.?. Assume L;-87 in, Lg-111 in., a-50 in., b-93 in, and c-39 in. If the normal stress in each steel bar must be limited to 19.4 ksi, determine the maximum load Pthat may be applied to the rigid bar. (2) (1) D Answer: P- kips.
Draw BMD and SFD for the beam shown below: 8 kN w 2 kN/m A 3 m B. 9 m 3 m Rp D.
ASAP PLSS I GIVE UPVOTEE ? ♥
Problem 1. A W30 x 116 beam hasthe top flange restrained againstlateral displacement and rotationand has an unstiffened web. A pointload is applied to the top flange at2m. From the left support. The beamspans 12 m. Use A36 steel with yieldstrength of Fy = 248 Mpa. a. Compute the maximum value of point loadthat may be applied without web yieldingoccurring. b. Compute the maximum value of point loadthat may be applied without web cripplingoccurring. Properties of W30 x 116d = 762 mmK = 41.28 mmbf = 266.7 mmtf = 21.59 mmtw = 14.33 mm
W 14 x 142 is used as a column having a length of 8.48 m. long. It is hinged at the r end and fixed at the lower end but there is a lateral bracing perpendicular to minor axis of the W section at a point 4.78 m. above the bottom support. It is assumed to be pinned connected at the bracing point. Using A 36 steel Fy= 248 MPa the NSCP Specificatioris. E, = 200000 MPa. Properties of W 14 x 142 A = 26967.69 mm2 d= 374.65 mm bf= 393.70 mm tf= 27.00 mm tw= 17.27 mm4 Ix= 695.11 x 106 mm4 Iy = 274.71 x 106 mm4 rx = 160.53 mm rY = 100.84 mm Assume: Kx = 0.80 for 8.48 m. length KY = 1.9 for the length on the upper support KY = 0.80 for the length on the bottom support Compute the slenderness ratio along y-axis. Please show clear solution thank you
A propped cantilever beam ABC (see figure) has a shear release just right of the mid-span. P = qL C A B Shear release- L L/2 L/2 – (a) Select the most economical wood beam from the table in Appendix G; assumeq = 55 Ib/ft, L = 16 ft, o = 1,750 psi, and t = 375 psi. Include the self-weight of the beam in your design. (Enter the nominal dimensions in inches.) in. x in. (b) If a C 10 x 25 steel beam is now used for beam ABC, what is the maximum permissible value of load variable q (in Ib/ft)? Assume o, = 21 ksi and L = 10.5 ft. Include the self-weight of the beam in your analysis. (Use the section modulus for axis 2-2.) as Ib/ft
A built up section of A992 steel, F, = 345 mPa is made from plates fully welded together. The flanges consist of PL16X380 and PL12X500 for the web. Use the NSCP 2015 specifications. PL16x380 WL = 1.5wp %3D A Wu = 3.6wp 10m Which of the following best gives the maximum service dead load, wp? 40.2 kN/m 26.8 kN/m O 10.8 kN/m O 96.6 kN/m PL12x500
W 14 x 142 is used as a column having a length of 9 m. long. It is hinged at the r end and fixed at the lower end but there is a lateral bracing perpendicular to minor axis of the W section at a point 6 m. above the bottom support. It is assumed to be pinned connected at the bracing point. Using A 36 steel Fy 248 MPa the NSCP Specifications. E= 200000 MPa. Properties of W 14 x 142 A-26967.69 mm2 d=374.65 mm bf=393.70 mm tf-27.00 mm tw 17.27 mm Ix 695.11 x 106 mm4 Iy = 274.71 x 106 mm4 rx = 160.53 mm ry 100.84 mm 221 Assume: Kx=0.80 for 9 m. length KY 1.9 for the length on the upper support KY-0.80 for the length on the bottom support CIVIL ENGINEERING- STEEL DENON a) Compute the slenderness ratio along y-axis. b) Compute the slenderness ratio along x-axis. c) Compute the safe axial load
Prob #l: Design uniform kive load of 22,500 Nm. exclusive of its own weight . Assume the beam to have a simple span of 6m. Use ACI Specs, with fe-20 MPa, f = 138 MPa., 'n=9, Va =0,09| fe and a rectangvlar beam reinforced for tension enly to carry a Va= 22,500 Nm figire : Prob #2: A beam having an 8m. simple span has a cross-section shown in the figure. Defermiìne the maximum concentrated load that this beam can carry besides its own weight. Use fe=7MP., f=124 ME. and n= 10. Figyre: 100 200 100 400mm 100 N.A. --N.A. 600mm 400 5Somm 200mm 550-X 150 n As OSt 4-25mmd Tensicn Bar 400mm
4.7-2 An HSS 10 x 6 x 6 with F 46 ksi is used as a column. The length is 15 feet. Both ends are pinned, and there is support against weak axis buckling at a point 6 feet from the top. Determine a. the design strength for LRFD. b. the allowable stress for ASD.