The gas 3. A stationary power plant operating on ideal Brayton cycle has pressure ratio of temperature is 300 K at the compressor inlet and 1300 K at the turbine inlet. Utilizing the air standard assumptions, determine (i) gas temperature at the exit of compressor and turbine (ii) work ratio (iii) thermal efficiency.

The gas 3. A stationary power plant operating on ideal Brayton cycle has pressure ratio of temperature is 300 K at the compressor inlet and 1300 K at the turbine inlet. Utilizing the air standard assumptions, determine (i) gas temperature at the exit of compressor and turbine (ii) work ratio (iii) thermal efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6
a(2-3)A gas-turbine power plant operates on Brayton cycle. The air pressure inside the combustion chamber is 1100 kPa. The pressure at the turbine exist is 1.10 bar. Using local thermometers on site, the maximum temperature reached in the system is 1311 K while the minimum temperature in the system is 22C. The working fluid is air, which enters the compressor at a rate of 120 m3/min and leaves the turbine at 460°C. Assume the compressor has no deviation. Determine: The compression ratio Turbine isentropic efficiency % Actual temperature inter the combustion chamber in K The net power output in MJ/day The thermal efficiency %|
In an Qtto cycle with compression ratio 9, the air pressure at the beginning of the compression process is 95 kPa and the temperature is 27 ° CJhere is a constant volume of 800 kJ / kg heat input into the cycle.In the light of this information, Question 1:Standard air containers (taking into account the change of specific heat with temperature), a) temperature and pressure at the end of heat input into the cycle. b) the net work of the cycle, c) thermal efficiency, and d) Calculate the average effective pressure. Question 2:Cold air standard containers (taking specific temperatures constant), a) temperature and pressure at the end of heat input into the cycle, b) the net work of the cycle, c) thermal efficiency, d) average effective pressure and e) Compared to question 1, the thermal efficiency obtained by taking the specific heats constant was calculated how many% wrong.(Note:The solution gives more accurate results with variable specific heats!) (Cv = 0,718kj / kgK and R = 0,287 kPa.…
pls ans quickly
An idealcold air-standard Brayton cycle produces some quantity of power. Air with a mass flow rate of 6 kg/s enters the compressor at 100 kPa, 300 K.It is also known that the compressor has a pressure ratio of 10 and the turbine inlet temperature is 1400 K.If k = 1.4for the working fluid, determine the thermal efficiency, the ratio of back work, and the net power for the cycle in kW.
A newly purchased sedan car operates on an ideal thermodynamic cycle. The engine has acompression ratio of 10. The ambient air pressure is 1 bar while temperature is 21 ºC. Themaximum temperature in the engine is 1600 K. Draw the ideal power cycle and label it.Utilizing the air-standard assumptions, determine (a) the gas temperature at the exits of thecompression and the expansion processes, (b) the specific works of compression, expansionand net, (c) heat supplied to the engine and (d) the thermal efficiency.
A reheat steam cycle has 13,580 kPa of throttle pressure at the turbine inlet and a 37.50308414 atm reheat pressure, the throttle and reheat temperature of the steam is 1302 R, condenser pressure is 4.3 kPa. If the efficiency at high – pressure and low – pressure turbine is 76% and 75%, determine the cycle efficiency, in percent.
A diesel cycle with air as the working fluid has a compression ratio of 20. The temperature and pressure in the first process is 20°C, 95kPa and the highest attainable temperature is 1927°C. The air standard assumptions are applicable, both Kinetic and Potential energy are negligible. The mass/mass flow rate is negligible. Use the standard constants for air (Cp, Cy. R, and k). Determine the amount of heat transferred and rejected, the net work and thermal efficiency, and the mean effective pressure.
High-P turbine Low-P turbine Reheater (4) Boiler P4 = P5 = Preheat Pump Condenser The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 °C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m3/kg Find the temperature in degree C at state 4 to 2 deciamal places.
On the diagram below sketch a basic Rankine cycle with superheating. Assume that there are irrevesibilities in the turbine and pump. Identify the device associate with each process. Make sure to label: the states and include important features, e.g. lines of constant temperature, volume, pressure, entropy, vapor dome, etc.
ASAB
please try complete solution.