The front view is indicated as a long arrow mark in the attached figure , figure out the three projection view of the iso figure shown below

Q: Draw the cavalier oblique projection of the object. Use 45° for the third axis.

A: Refer the following Cavalier Oblique view of the given orthographic views.

Q: As per the given dimensioned  top and front view  Sketch the isometric and side view of the…

A:

Q: Draft and annotate the 2D sketch of housing using AutoCAD and mention all the dimensions. Colour the…

A:

Q: Sketch the three view of the given view using creo and also show the hidden line of the attached…

A:

Q: Sketch the orthographic projection as per the answer arrangement (a) top view (b) side view (C)…

A:

Q: The given sketch is a view of modified “Plate" one view. Sketch the 2D sketch of the below figure…

A:

Q: Draw, using 1 st angle projection Orthographic view of the following figure  with  suitable scale,…

A: (a) the given front elevation;

Q: Can you please send me top,front and right view of the given diagram with correct dimensions.

A: The isometric view is given in the diagram.

Q: Draw in full scale the front view (indicated by the arrow A), top view and right-side view of the…

A:

Q: 66 Through holes Through hole 70 sketch the orthographic view using catia v5, and i need the…

A:

Q: Show the working view ,help me by showing step by step to sketch the orthographic view of the…

A: open creo parametric software then open new  part , sekect the XZ plane and edit the skecth and draw…

Q: Draw the isometric view of a square-headed bolt 24 mm diameter and 70 mm long, with a square neck 18…

A:

Q: AutoCAD Sketching The given sketch is a cross section view of housing. Sketch the 2D sketch of the…

A:

Q: Draft and annotate the 2D sketch of cover using AutoCAD and mention all the dimensions. Colour the…

A:

Q: for the given figure , draw the 2d sketch using AutoCad and give the dimension

A:

Q: Draw an orthographic drawing in a title block using 3nd angle projection techniques for the…

A: Required orthographic views and sectional front view are drawn on grid paper. 1 Grid = 1Unit

Q: sketch the Orthographic view for the given isometric view

A:

Q: for the above isometric view , sketch the orthographic view in first angle proiection using catia v5…

A:

Q: 14.sketch the orthographie iew i need the orthographic view in the first angle projection also…

A:

Q: Can you send me the top, front and right view of the given diagram with correct dimensions

A: The isometric view is given in the diagram.

Q: Can you send me the top,front and right view of the given diagram with correct dimensions

A: Draw the top,front and right view of the given diagram with correct dimensions.

Q: Use blank or isometric grid paper to draw the isometric views of the following objects.

A: Draw the given three views.

Q: Sketch the isometric and Orthographic projection of the given componet Top view Side view Front…

A:

Q: Sketch the 2D figure of cover using AutoCAD and mention all the dimensions, colour the hatched lines…

A:

Q: Draw the three projections of the following figure using AutoCAD software and send the solution in…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Sketch the missing side view and isometric view .  Use CREO parametic 3.0 to sketch the figure…

A:

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: The below figure shows two views of a bolster block. Draw, using 1 st angle projection and a…

A: (a) the given front elevation;

Q: Sketch the top, front and right side views of the isometric. Scale the orthographic views so that…

A: The given figure consists of a isometric view of a component  To sketch an orthographic view

Q: The following figure shows an isometric view of an object.Draw its Front view,Top view,and Side view…

A: Draw front view , side view and top view

Q: Draw the three projections of the body in Figure 1- using AutoCAD 1-Do not write the dimensions on…

A: Find Draw the three projections of the body.

Q: Q2. Write the full details of AutoCAD commands to create the three-dimensional solid model shown in…

A:

Q: Sketch the orthographic projection of the given isometric sketch Front view Top view Side view

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.