The forces F1={−5i+4j−4k}kN and F2={5i−3j−2k}kN act on the end of the beam. Replace these forces by an equivalent force and a couple of moment acting at point O. (Figure 1) Determine the resultant force.   Determine the equivalent resultant couple moment about point O Enter the x, y, and z components of the force separated by commas

Q: The 39N force P is applied perpendicular to the portion BC of the bent bar as shown in Figure 1. a)…

A:

Q: The lower ends of the three steel bars in Figure are at the same level before the applied…

A:

Q: Solve for the moment about point O produced by the forces P and F. The magnitude of P is (4740/2) lb…

A: Given data in question  I section Dimensions  Point loads passing through point O Angle of action of…

Q: Please answer. This is about couples.

A:

Q: 1. A 250mm x 300mm beam has a simple span of 12 meters. It is necessary to place a support at…

A: Deflection: The displacement of any structural element in the structure which is displaced under the…

Q: Problem 1: A beam is supported by a roller at A and a pin at B. Determine the reactions at A and B…

A:

Q: A B E -smt-sm-sm-5 m – Consider the beam in the figure without the applied load. If support C…

A:

Q: When the two forces are placed on the beam, the diameter of the steel rod (E-200GPa) BC decreases…

A:

Q: a. Determine the magnitudes of the forces T2, given that the resultant force of 210 N is acting…

A: given data: a. Determine the magnitudes of the forces T2, given that the resultant force of 210 N is…

Q: 1. In the figure represents the concurrent force system acting at a joint of a bridge truss.…

A: Given data  Find P and F value

Q: w2 w1 B Determine the shear force and bending moment in the beam. Use wl = 22 kN/m, w2 = 25 kN/m, a…

A:

Q: 20 KN/m 40 KN 1. А Ac 8 m 8 m 3 m 3 m

A:

Q: Ql:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three…

A: Given the coplanar system of forces and moments

Q: Give the equations needed to solve for the member forces and support reactions for the figure. All…

A:

Q: Q1. the resultant's line of action intersects member AB, measured from point B. Also show the force…

A: Consider the free body diagram ;

Q: 3. Completely determine the resultant and moment with respect to O of the force system shown in the…

A:

Q: Determine the reactions for the beam in the given figure. When & uniform load is applied, the fixed…

A: E = 30000 Kips/in.2I = 240 in.4Support B settle (∆) = X = 0.2 in. Determine the support reaction of…

Q: fixed in the middle motor 2. A rotating of the weighting 3 ton (mass) is 52,36 jad/sec two simple…

A:

Q: Q1:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three…

A: From the given co-planar system of forces in the figure,

Q: Consider the following simple truss in Figure 2. F, = 35kN. Fz = 18KN. F 34kN. a) Determine the…

A: Find the resultant in x-direction:Rx=-35+18sin30Rx=-26kNFind the resultant in…

Q: Cut a cross-section through the beam and draw a free body diagram to the left of the cut. Determine…

A:

Q: The magnitudes of the forces shown are FB = 800 lb, FC = 1000 lb and FD = 900 lb. Solve for the…

A: Magnitude force is the total of all forces acting on a body The magnitude of the net force acting on…

Q: of a wall. The beam is subjected to a X KN concentrated load at 2 m. from the wall and a uniformly…

A: For Shear Force and Bending moment we take help of equilibrium condition. Standard result of…

Q: 1. Four forces are applied to point P as shown. Knowing that F₁ = 50 lb, F2 = 20 lb and F4 = 70 lb,…

A:

Q: Determine the moment of the vertical reaction at point A (A,) rotating about the location (XR) of…

A:

Q: 1.) Use the Triangle Rule and the Law of Cosines to find the magnitude of the resultant force FR =…

A:

Q: 1. For the Force Pin the Figure, determine the components P1 and P2. Given that P1 is directed 80…

A:

Q: The lower ends of the three steel bars in Figure are at the same level before the applied…

A:

Q: Determine the reaction forces of the roller support at A and pinned support at B. You can use the…

A:

Q: QI:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three…

A: Using the system of coplanar forces given,

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.