12) The force P is applied at d = 50 mm from the bottom as shown.Compute the normal stress at section a-a at the specific points.200 mmC200 mmdi20 mm300 mm-aWhat is the normal stress in MPa at point C at the center if P =65.5 kN? If Compressive add a minus sign inyour final answer, Use 2 decimals.

The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section a-a at the specific points. a C+ 200 mm P 200 mm d. 20 mm -300 mm- a What is the normal stress in MPa at point C at the center if P =65.5 kN? If Compressive add a minu your final answer, Use 2 decimals. B

The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section a-a at the specific points. a C+ 200 mm P 200 mm d. 20 mm -300 mm- a What is the normal stress in MPa at point C at the center if P =65.5 kN? If Compressive add a minu your final answer, Use 2 decimals. B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1)) Define the following: A) Sand Casting B) Die Casting C) Casting mold cavity D) Casting mold pattern E) Casting mold cope and drag F) Casting mold parting line.
8 - Obtain the center of gravity of the surface area of the plane plate of constant thickness in the given set (x,y). Dimensions where a = 12 m, b = 23 m and r = 3 m, the center of the circle is at the point (2a, 1/2 b). Which of the following is the correct coordinate of the center of gravity of the plate on the y-axis?A) 13.34B) 19.94C) 17.14D) 19.05E) 10.87
11 - A) 15.6 kN B) 10 kNC) 20 kND) 17.8 kN E) 12.5 kN
!
Be sure to include units with your answers. Show your work. 40 mm X = Y = 60 mm 50 mm X 1) 8 pts) Find X for the centroid of the shape above. 2) 8 pts. Find Y of the shaded shape below. Ľ
138) Which one is needed to produce perforated parts using casting technique?a) lower degreeb) high degreec) spadesd) runnere) feeder 139) what is the crystal structure of iron?a) Hexagonal tight-packed structureb) volume-centered cubicc) face-centered cubicd) simple cubice) Ortok141) How is the elastic modulus calculated?A) With the strain rate of strainB) The ratio of shear strength to deformationC) the ratio of strain to strainD) the ratio of tensile strength to strainE) by the ratio of yield strength
22 - A steel pipe with a cross section area of 100 cm2 is subjected to pressure along its axis. What should be the maximum compressive stress of the material from which the pipe is made so that the pipe can safely carry a load of 500 kg? A) 150 daN / cm2B) 150 N / cm2C) 15 N / cm2D) 50 N / cm2E) 5 N / cm2
a) 1. The support reaction forces at the A and C, in terms of P,be careful of the sign. 2. Give the expressions of the shear and moment at an arbitrary poistion x of AB segment, in terms of P and x, be careful of the sign. 3. Give the expressions of the shear and moment at an arbitrary poistion x of BC segment, in terms of P and x, be careful of the sign. b)Given l= 1000 mm, P= 4000 N and l1/l=0.66, calculate the internal shear force and draw the moment diagram
7- Which of the following statement is not true: Biomechanics is the science that combines the field of engineering with the fields of biology and physiology. Biomechanics concerns with the human body. Biomechanics is not a young science. Biomechanics applies the concept, the design, the equipment, the analysis, and the systems of the mechanics in biology and medicine Biomechanics is a young science a) b) c) d) e) 8- Elasticity and stiffness are both material properties, such that: а) They are two contradictive properties that work in an opposite manner.
In the Figure 6, the absolute force value in the bar AB is (in kN): Figure 6: y 5 m A 20 kN 5 m 5 m B Choose the answer A) 10.55 B) 8.55 C) 11.55 D) 9.55
Chose the correct answer: 5. A point load is considered in a system: a) A load applied at a dimensionless point b) That the load is considered punctual is applied in an area that is considered small along the length of the beam c) That the load of the point load is small with respect to the length of the beam d) All of the above e) None of the above
Select the right value of the stress occurred on a hollow shaft when it is subjected to a twist of 5° over its entire length. Assume the shaft has a wall thickness of 7mm, is 2.5m long and has an internal diameter of 26mm. (use G=80 GPa) a) 2400 GPa b) 55.85 MPa c) 5585 GPa d) 42.96 MPa e) None of above