The force F =84 N acts on the end of the pipe at B. (Figure 1) Part B Determine the magnitude of the maximum moment of the force F about point A. Express your answer to three significant figures and include the appropriate units. HA MA max Value Units Figure 1 of 1 Submit Request Answer Part C Determine the angle 0min (0°< Omin <180°) of the force F that will produce minimum moment about point A. 0.9 m Express your answer using three significant figures. F VO AZO vec -0.3 m-- -0.7 m Oin P Pearson 13:1 22.04.2

The force F =84 N acts on the end of the pipe at B. (Figure 1) Part B Determine the magnitude of the maximum moment of the force F about point A. Express your answer to three significant figures and include the appropriate units. HA MA max Value Units Figure 1 of 1 Submit Request Answer Part C Determine the angle 0min (0°< Omin <180°) of the force F that will produce minimum moment about point A. 0.9 m Express your answer using three significant figures. F VO AZO vec -0.3 m-- -0.7 m Oin P Pearson 13:1 22.04.2

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The torque required to drive a machine varies with angle over each revolution as shown in thediagram.i. Calculate the work done per revolution and the mean torque.ii. If the mean speed of the machine is 200 rev/minute, what is the mean power?
Dynamics of Rigid Bodies Please help ASAP. Rate will be given accordingly. Please answer correctly. Please write your answer on paper. Thank you so much. Note: The tolerance is ±1 in the third significant digit.
Help me
Data has been gathered from a lifting system used to trans port engine parts. The sys tem consis ts of a drum and cable. The following data was obtained when the drum lowers the load (assume cons tant acceleration). Drum diameter = 1m Mass of load - 9kg Initial velocity =0 m/s Time to des cend- 64 secs Distance travelled 0.7m You have been asked to use this information to determine: Cable a) The final linear velocity of the load b) The linear acceleration of the load Load c) The final angular velocity of the drum d) The angular acceleration of the drum e) The tension force in the cable f) The torque applied to the drum Fioure 1 solve (d),(e),(f) parts and please mention kinematic equations which need to solve this question
Provide a complete solution to each problem. 1. Two painters are carrying a uniform horizontal ladder that is 12 feet long and weighs 200 N. If one person applies an upward force equal to 85 N at one end, at what point does the other person lift? 2. A uniform ladder 10.0 m long and weighing 50.0 N rests against a smooth vertical wall. (a) If the ladder is just on the verge of slipping when it makes a with the ground, find the coefficient of static friction between the ladder and ground. (b) If the coefficient of static friction is 0.360, and the same ladder makes a angle with respect to the horizontal, how far along the length of the ladder can a 65- kg painter climb before the ladder begins to slip?
(Figure 1) Part A If gear A rotates with a constant angular acceleration of a = 90 rad/s? , starting from rest, determine the time required for gear D to attain an angular velocity of 600 rpm. Gears A, B, C, and D have radii of 15 mm, 50 mm, 25 mm, and 75 mm, respectively. Express your answer to three significant figures and include the appropriate units. HẢ Value Units Submit Request Answer Figure < 1 of 1 Part B Also, find the number of revolutions of gear D to attain this angular velocity. Express your answer to three significant figures and include the appropriate units. vec ? Op = rev. Submit Request Answer
Pendulum A pendulum swings back and forth. The angular displacement uof the pendulum from its rest position after t seconds is given by the functionu(t) = 20 cos (3pt), where u is measured in degrees (Figure 13). Find all times atwhich the magnitude of the angular displacement (absolute value of u) is greatest.
A 3 meter long beam with weight 300 N is supported by a hinge at the wall and a cable as shown. A 300 N block is positioned along the beam at a distance x from the wall. If the breaking strength of the cable is 500 N, what is the maximum value of x? Explain all steps
What is the period of oscillation (in seconds) of a rod of length 4.09m that is fixed at one end, but otherwise free to rotate without any friction, which has a mass 4.18kg, for small displacements? Note: In the space below, please enter you numerical answer. Do not enter any units. If you enter units, your answer will be marked as incorrect.
Show all steps. 1. A 100-kg nonuniform boom that is 6.0 m long is loosely pinned at the pivot at P. A 600-kg concrete block is suspended from the end of the boom at A, as shown in the figure. The boom forms a 30° angle above the horizontal, and is supported by a 4.0-m cable between points D and B. Point B is 4.0 m from P, and point D is 4.0 m above P. The center of mass of the boom is at point C, which is 2.0 m from P. Assume that all the quantities shown in the figure are accurate to two significant figures. What is the tension in the cable connected between points B and D? 4m 2m 4m L. 2m C 30°
In figure shown, the mass of block A is 50 kg. The coefficient of static friction for all surfaces of contact is 0.10, determine the minimum mass of B to maintain equilibrium of the system. Assume the pulleys to be frictionless and use B = 75°, e = 70° and a = 65°. %3D
Two cables are tied together at C and are loaded as shown. Part 1. If W = 205 lbs, determine the tension (a) in cable AC and (b) in cable BC. Part 2. Determine the maximum value for W such that the tension will not exceed 220 lb in either cable.