The following two claims are made by salesmen about newly invented 2-phase adiabatic compressors. Salesman A: "It can compress steam with a quality of 0.1 from 100 kPa to saturated liquid at 400 kPa. Salesman B: "It can compress steam with a quality of 0.1 from 100 kPa to saturated liquid at 1000 kPa. a. Show both claims on a T-S (temperature vs. specific entropy) diagram. b. Which claim or claims are possible? c. Which claim or claims are impossible? "1 "

The following two claims are made by salesmen about newly invented 2-phase adiabatic compressors. Salesman A: "It can compress steam with a quality of 0.1 from 100 kPa to saturated liquid at 400 kPa. Salesman B: "It can compress steam with a quality of 0.1 from 100 kPa to saturated liquid at 1000 kPa. a. Show both claims on a T-S (temperature vs. specific entropy) diagram. b. Which claim or claims are possible? c. Which claim or claims are impossible? "1 "

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Termodynamic question I NEED ANSWER RARIDLY PLEASE!!! Water vapor enters the steam turbine at 4000 kPa pressure, 500 ° C temperature and 6 m3 / h volume flow, shown in the figure below. 0.2 times the mass flow rate of the incoming water comes out of the outlet no. 2 with 500 kPa pressure and 200 ° C temperature. 0.8 times the mass flow rate of the water comes out of the outlet no.3 with 30 kPa pressure and 0.85 dryness degree. Since the heat transfer from the turbine to the environment is 5000 kW, Find the mass flow rate of the incoming water. Find the volume flow of water at outlet no. 3. Find the power (kW) produced by the turbine. (Changes in kinetic and potential energies are negligible)
Read the question carefully before answering. Box or indicate your final ansurers when solving and draw your diagrams cleanly. Complete solution please. Use 2 decimal places when solving and for final answers. Draw the PV and TS diagram with proper label of points when required. 1. An Otto Cycle receives air at 101 kPa and 20c, then compresses it to 10% of the original volume. The max temperature of the air is 1050 K. Draw the PV and TS diagrams, and selve for the following: the remaining temperatures, QA, QR. Whet and efficiency.
Solve both please
the subject is thermodynamics 2. please answer my question. thanks
PLEASE FOLLOW THE INSTRUCTION.
Please match the formulate (energy and/or mass balance) to the corresponding steady flow devices: A not well insulated nozzles by neglecting the potential energy change. An adiabatic turbine by neglecting the kinetic and potential energy change. A not well insulated compressor by neglecting the kinetic and potential energy change. An adiabatic mixing chamber with two inlets and one exit by neglecting the kinetic and potential energy change. An adiabatic throttling valve by neglecting the kinetic and potential energy change. A. B. C. D. E.
PLEASE FOLLOW THE INSTRUCTION.
2. In Otto Cycle, air at 18°C is first compressed to one-ninth of its original volume. If the heat input to the cycle is 460 KJ/Kg of air, determine a. The temperature of the remaining points in the cycle. b. The ratio of the maximum and minimum pressure in the cycle.
104#1. an ideal gas with R=0.062 BTU/lbm-degree R and Cv=0.158 BTU/lbm-degree R undergoes athree process cycle in a cklose system. from the initial state of 20 psia and 570degree R, the gas is compressed at coinstant pressure to 1/5 of its initial volume, process 1-2; it is then heated isochrocally to state 3, process 2-3; and finally, it expands polytopically with index n=1.5 back to its initial state, process 3-1. determine the pressure, specific volumes and temperatures at cardinal points around the cycle and the cycle thermal efficiency.
Select the correct expression for steady flow work of a reversible compressor_________ A. B. C. D.
_.. A steam compressor operates with P₁ = 100 kPa and x1 = 1 at the inlet, a final pressure of 1600 kPa at the exit, a mass flow rate of m = 5 kg/s, and an isentropic efficiency of n = 85%. Complete a thermodynamic analysis of the compressor, using the appropriate data for water, by finding: (A) The isentropic temperature at the exit, T2s, (B) The actual temperature at the compressor exit, T2, and (C) the rate of entropy production of the compressor, $gen. W