The following results were obtained from a shear box test for a soil sample and the dimensions of the shear box are (60 *60 ) mm. Caleulate the shear strength parameters (¢ and 0). Normal Load (kN T 0275 | 0550 Shear Load (kN) | 0179 | 0269 |

The following results were obtained from a shear box test for a soil sample and the dimensions of the shear box are (60 *60 ) mm. Caleulate the shear strength parameters (¢ and 0). Normal Load (kN T 0275 | 0550 Shear Load (kN) | 0179 | 0269 |

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A set of three unconsolidated undrained triaxial compression tests were also performed on soil…

A: A set of three unconsolidated undrained triaxial compression tests were also performed on soil…

Q: Solve this problem graphically and then analytically. A CU triaxial test was performed on a dense…

A: Introduction Stress is a physiological term in continuum mechanics that describes the internal…

Q: Using a deviator stress vs axial strain diagram, explain how the failure stress increases with cell…

A: Multiple questions in single pic...answering first question

Q: Portions of the time histories of deviator stress and axial strain from a stres triaxial test are…

Q: A unconfined compressive strength test was performed on a clay sample. The sample had a diameter of…

Q: A series of direct shear tests have been performed on a soil, using a circular shear box with a…

A: Given, Diameter (D) = 2.5 in Direct shear test data

Q: The table shows the results of a consolidated undrained (CU) test on a overconsolidated clay soil…

A: For sample 1 σ1 =15+20-10σ1 =25 kpaσ3 =15-10 σ3 =5 kpaRelation of major and minor stress is given…

Q: A very long steel drill pipe got stuck in hard clay at an unknown depth. The drill pipe was applied…

Q: asure the shear strength of a clayey soil san ress of 50 kPa, and to be 65 kPa at an effecti n angle…

Q: Q-1: Direct shear tests were performed on a dry, sandy soil. The size of the specimen was 50 mm x 50…

Q: 14. An unconfined compression test was performed on a soil sample having a height of 3 inch and a…

Q: A series of direct shear tests was performed on two types of soil. The recorded data of normal…

A: The given data is shown below:

Q: Three specimens of clay having a small air-void content were tested in the shear box. Shear loading…

A: Solution:- Given data:- Normal stress (kN/m2) 145 241 337 Shear stress (kN/m2) 103 117 131…

Q: In plastic failure, load corresponding to strain is arbitrarily taken as the failure load 10% 15% 5%…

A: Disclaimer Since you have asked multiple question, we will solve the first question for you. If you…

Concept explainers

Test for Determination of Shear Strength

The term shear strength is often associated with the soil. Shear strength is defined as the resistance to the deformation of soil particles due to the continuous action of shear stress. In short, shear strength is the maximum shear stress that a soil can sustain.

Question

The following results were obtained from a shear box test for a soil
sample and the dimensions of the shear box are (60 *60 ) mm. Calculate the
shear strength parameters ( c and 0).
1.10
Normal Load (kN)
Shear Load (kN)
0.275
0.550
0.179
0.269
0.447

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Shear parameters:

VIEW

Step 2: Calculate the shear parameters:

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Test for determination of shear strength

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

use the attached graph paper) A series of direct shear tests was performed on a soil sample. Each test was carried out until the specimen sheared (failed). The laboratory data for the tests are tabulated as follows. Determine the soil's cohesion and angle of internal friction. Specimen Number 1 2 3 4 Normal Stress (kN/m²) 1200 1900 3000 4875 Shearing Stress (kN/m²) 2175 2310 2910 3615
Please answer fast. Im struggling!
I need the answer as soon as possible
A sample of dry, cohesionless soil has an angle of internal friction of 35°. If the minor principal stress is15 lb/in2, at what values of deviator stress and major principal stress is the sample likely to fail? KINDLY GET THE RIGHT ANSWER WITH EXPLAINATION STEPS
Assume that both a triaxial shear test and a direct shear test are to be performed on a sample of dry sand. When the triaxial shear test is performed, the specimen fails when the major and minor principal stresses are 80 and 20 lbs/in^2, respectively. When the direct shear test is performed, what shear strength can be expected if the normal stress is 4000 lbs/ft^2?
Question Table 1 gives data from a standard shearbox(direct shear) test on a sample of 125g of dry sand. The initial dimensions of the sample were 60mmx60mm on plan x20mm in height. The test was caried out at a constant normal effective stress of 50k:Pa. Take the specific gravity of the soil grains Gs=2.65. Plot graphs of (a) shear stress t against shear strain y; (b) volumetric strain evol against shear strain y; (c) specific vohume v against shear strain y. (d) Comment on these graphs and estimate the peak and critical state effective angles of friction of the soil. Table 1: Shearbox Data Relative horizontal Upward vertical movement Shear stress t (kPa) displacement x (mm) of shearbox lid y (mm) 0.00 0.000 0.02 0.002 19 0.04 0.008 34 0.06 0.016 43- 0.08 0.026 47 0.20 0.064 56 0.32 0.128 51 0.48 0.192 46 0.64 0.256 41 0.80 0.288 37 0.96 0.320 34 1.12 0.321 33
A triaxial compression test was conducted on a saturated soil sample to determine its shear strength parameters: effective cohesion (C') and effective friction angle (O'). The confining pressure used during the test was 30 psi. The deviator stress on the sample at the time of failure was 40 psi. The porewater pressure measured at the time of failure was 5 psi a) The figure below shows the stress conditions on the sample at the time of failure. Provide the values of total stresses, o1 and oz on the sample. Total horizontal stress, o3 (psi) = (Report to the nearest whole number, i.e. no decimals) Total vertical stress, o1 (psi) (Report to the nearest whole number, i.e. no decimals) %3D b) The figure below shows the effective stress Mohr's Circle for the above soil sample at failure. What are the values of effective normal stresses at points A and B?
A structural engineer has hired you to design square concrete unembedded footings for a building, based only on capacity. Each footing will hold an axial load of 340 kN. Your technicians have conducted lab tests on specimens sampled from the site, and they report the following profile: a 0.8m thick clay layer over a 7m thick clayey silt layer (the clayey silt layer lies over rock). The lab report reveals that the clay has a friction angle of 34 degrees and an undrained strength of 35 kPa, and that the clayey silt has a friction angle of 37 degrees and an undrained strength of 45 kPa. Determine the size of one of the footings, in meters, such that the critical actor of safety against a capacity failure is as close to 3 as possible, but still larger than 3 and smaller than 3.2. The other (non-critical) factor of safety must be greater than 3. Express your answer with a resolution of 0.1 meters. That is, values of B of 1.2, 2.3, 3.4m, etc., for example, are acceptable, whereas B values of…
Assume that both a triaxial shear test and a direct shear test are to be performed on a sample of dry sand. When the triaxial shear test is performed, the specimen fails when the major and minor principal stresses are 80 and 20 lbs/in^2, respectively. When the direct shear test is performed, what shear strength can be expected if the normal stress is 4000 lbs/ft^2? Show all work.
Soil
ANSWER PLEASE THANKS ASAP!
A series of direct shear tests were conducted on a sample of soil in a 60 mm square shear box. The table below shows the results that were obtained at failure. Plot the graph of shear stress at failure against normal stress anddetermine the strength parameters of the soil. Normal Load (N) 200 300 400 Shear Load (N) 105 142 180