The following data is provided for a switching power pole. Drain voltage V₁ = 10V Drain current ID 5A Switch resistance RDS ON = 25m Switch conduction loss Pcon loss = 0.312W Switching on loss PSW ON = 0.1W Switching off loss Psw off = 0.125W If the switching frequency is 100kHz, determine: (1) The operating duty cycle. (ii) The Switching on time. (iii) The Switching off time.

The following data is provided for a switching power pole. Drain voltage V₁ = 10V Drain current ID 5A Switch resistance RDS ON = 25m Switch conduction loss Pcon loss = 0.312W Switching on loss PSW ON = 0.1W Switching off loss Psw off = 0.125W If the switching frequency is 100kHz, determine: (1) The operating duty cycle. (ii) The Switching on time. (iii) The Switching off time.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ВЗ Draw the block diagram representation of linear ramp type digital voltmeter and name the blocks.
Question 15 Which of the following statements are correct (select all that apply, there may be more than one correct option)? Germanium is an excellent semiconductor for LEDs Above threshold, light in a laser arises mainly from stimulated emission of photons O Light is emitted from an LED by spontaneous emission of photons in reverse bias O The energy of photons emitted from an LED is approximately that of the band gap of the semiconductor
In reference to the given circuit, what is the peak load voltage, Blank 1 if the diode drop is 0.65V? (UNITS in volts). Round off your FINAL ANSWER 2 decimal places. {Numbers only} 110 VRMS 60 Hz Sine Wave Vin 10:1 N1 N2 N3 BA281 1N3492 Vout R 500
Haritalar A (99+) Academia.ed... BUZEM Türkçe (tr) ▼ O Power Electronics_1 slerim / Çeşitli / MÜHENDİSLİK FAKÜLTESİ / Elektrik Elektronik Mühendisliği (İngilizce) / E2E350_Power Electronics 1/ 10 For controlled half wave rectifier, R=84ohm, f=50Hz and Vm=280V and a=1,5 rad. Calculate the power (W) absorbed by the load. Yanıt: In your calculations, take 3 digits after the comma and take pi = 3,14; Enter your answer into the system in terms of the desired unit only as a number.
AHorne Anywhere Section : 1 of 1 Question:2 of 7 Marks for this Question: 10 Upload answer sheets The diode current is 1.6 mA when the applied voltage is 180 mV, and 34 mA when the applied voltage is 465 mV. Determine n. Assume (KT/q)= 18 mV. Once you upload files from your second device, click on Syn OCamera Finish Do not altem Switching to another window or minimi
Quiq plz
Please answer in typing format
A (0 – 6) A range ammeter has inaccuracy of ± 2 .0% of its full scale. Calculate the % error in instrument if the expected value is (i) 2 A and (ii) 3A.
dont use ai and please explainQ1 a) If a 16MHz crystal drives the standard 8051, what is the period of one clock pulse? b) Calculate the period (duration) to execute the instruction "MUL AB."
Question 1 AC supply voltage with f=50-Hz is connected to a bridge rectifier via a step-down transformer if the rectifier output is connected to a resistive load with 472 and the output power seen across the resistor is 2.5-watt a) Calculate the output peak voltage and current b) Calculate the secondary and primary ms voltages seen across the transformer c) Calculate the secondary and primary peak-currents seen across the transformer ) Draw the output instantaneous voltage and current showing the relevant peak and DC quantities c) Derive the instantaneous equations for the output ac voltage and current (seen across the resistor) Hint: use the 2" approximation (practical model) N-100 turns N-20 turns D3 DI f= 50 Hz D2 D4 R=470 R-2.5w
Please can you design and draw the solution to this question.
Kindly describe and show the illustration as well. Thank you.