The floor of a light storage warehouse is made of 150-mm-thick lightweight plain concrete. If the floor is a slabhaving a length of 7 m and width of 3 m, determine theresultant force caused by the dead load and the live load.Note:FLOOR FILL (from Table 204-2)Lightweight concrete, per mm --- 0.015 kPaSTORAGE (from Table 205-1)Light --- 6.0 kPa

Given:- The thickness of the lightweight plain concrete = 150 mm Length of the floor = 7 m Width of…

Answered: The floor of a light storage warehouse…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A concrete slab to be used for a given runway used by a design aircraft 727-200 dual – wheel gear of 150000 Ib gross weight. The 90- day flexural strength of concrete is found to be 800 psi. The modulus of subgrade reaction is 200 pci, and the annual equivalent departures were expected to be 15000. The required thickness of concrete runway slab to carry the design aircraft is ................. in.
Concrete column with 4 steel rods 40 mm diam each. Size of column is 0.6m. Load is 40 tones. E of concrete can be taken as 40 GPA, E steel 200 GPa. Find: energy stored in the column?
Q-civil Concrete formwork Ata temperature of 50°F, 150 lb per cu ft of concrete is poured into a 14-foot-tall column form. Since there is no retarder, the concrete is Type I. Concrete will be poured to a depth of less than 4 feet with typical internal vibration. The placement speed is 7 feet per hour.
A floor panel 3 4 m wide and 12 m long is intended for a vibratory machine in a factory. The concrete to be used has a strength of 27.6 MPa (whose density is 1800 kg per cubic meter) and reinforcement used has yield strength of 280 MPa Determine the minimum thickness of slab if the panel is cantilever
1/ Calculate maximum deflection of the beams (This was solve it) 2/ Check the suitability of the section assuming the code limitation of L/240. 3/ If maximum deflection doesn’t meet the code requirement, propose your solution
Urgent Please help me
CONCRETE PRESSURE We are pouring 12-foot-high concrete columns with self-consolidating concrete, and each column can be placed in an hour. The concrete sets after about 8 hours. If the self-consolidating concrete weighs 170 lb/cf and has a chemical coefficient Cc of 1.4, what is the maximum pressure on the column forms?
Problem- A doubly reinforced rectangular concrete beam has a width of 30mm and an effective depth of 500 mm. The beam is reinforced with 2200 mm² of steel in tension and 628 mm² of steel in compression. The effective cover for compression steel is 50 mm. Assume that both tension and compression steel yield. The grades of concrete and steel used are M20 and Fe250, respectively. The stress block parameters (rounded off to first two decimal places) for concrete shall be as per IS 456 : 2000. Find the depth of neutral axis.
33. In M20 concrete M refers to [ C. Mix proportion В. Махimum 34. At an early age greater strength contribute compound is B. C2S A.Minimum D. None [ A.C;S С. СЭА D. C4AF
*I E,90 KB/S H.W (4)-2nd cours... Concrete technology H.W (4) (A) Give reasons: Very early strength of concrete increases if temperature during placing and setting is increased. This is not the case for concrete strength after 7 days. (B) / Explain the following curve (use your own words (DO NOT COPY FROM THE LECTURE & DO NOT COPY FROM OTHER RESOURCES). 10000 Age at Test ePonded 8000 Hessian days 6000 bnded Hessian 4000 Ponded days Hessian Ty 2000 032 040 Woter / Cement Ratio 036 044
i need clear ans and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛
Question 1: Consider a 600 mm deep reinforced concrete cantilever beam supported by a 600 mm square column as shown in the figure below. The beam reinforcement is anchored into the column. Minimum stirrups are provided in the anchorage zone according to CSA A23.3-19. Regular uncoated bars are used in the design. Material properties: fe= 35 MPa (normal-density concrete) and fy= 400 MPa. 1. Determine the largest beam rebar size that can be used without hook in this design according to the CSA A23.3 requirements. 2. Design the anchorage zone if the diameter of the longitudinal steel bars is 25 mm. 40 clear- 600 mm 40 clear 600 mm,

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS