The figure shows the cross section of a wall made of three layers. The thicknesses of the layers are L1, L2 -0.700 L1, and L3-0.250 L1. The thermal conductivities are k1, k2 - 0.820 k1, and k3-0.660 k1. The temperatures at the left and right sides of the wall are TH-30 °C and Tc- -20 'C, respectively. Thermal conduction is steady. (a) What is the temperature difference AT2 across layer 2 (between the left and right sides of the layer)? If k2 were, instead, equal to 1.060 k1, (b) would the rate at which energy is conducted through the wall be greater than, less than, or the same as previously, and (c) what would be the value of AT2? k2 k3 TH Tc L1 L9 L3

The figure shows the cross section of a wall made of three layers. The thicknesses of the layers are L1, L2 -0.700 L1, and L3-0.250 L1. The thermal conductivities are k1, k2 - 0.820 k1, and k3-0.660 k1. The temperatures at the left and right sides of the wall are TH-30 °C and Tc- -20 'C, respectively. Thermal conduction is steady. (a) What is the temperature difference AT2 across layer 2 (between the left and right sides of the layer)? If k2 were, instead, equal to 1.060 k1, (b) would the rate at which energy is conducted through the wall be greater than, less than, or the same as previously, and (c) what would be the value of AT2? k2 k3 TH Tc L1 L9 L3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer the question with explicit scheme and calculation is done until the second time!
A multi-layered wall with the dimensions shown in the figure has temperatures of 200°C and 50°C over the left and right surfaces, respectively. If the thermal conductivities of the wall materials A and C are k-60 W/m-K, k-24 W/m-K. If total rate of heat transfer through the wall is 175 W, what is the thermal conductivity of material B? T- 200°C T-soc 6 cm- 2 om 25 om
1) A wall section composed from the outside to inside, of concrete brick 100mm thick, an air space of 50mm, two layers of fiberglass insulation 38mm thick, concrete block 150mm thick and air space of 19mm and a gypsum board of 13mm. The exterior conditions are -20C and RH=90% while the interior conditions are 23C and RH=40%. The surface temperature from the outside to inside are shown in the figure. The permeances are: Still Air: µ = 175 ng/pa.s.m Fiber glass: M=2560 ng/pa.s.m? Concrete block: M= 200 ng/pa.s.m? Gypsum board: M= 2000 ng/pa.s.m? Concrete brick: µ = 4.55 ng/pa.s.m Determine if there is a risk of condensation, and if there is, what is the condensation rate? What would happen if a vapor barrier (M=0.2 ng/pa.s.m²) was installed on the warm side of the insulation (Surface 4). 21с 19C 16 С 12C -10 -15C -18C -19C Gyp Air Concrete Fiber Fiber Air Concrete Outdoor Indoor sum block Glass Glass brick 230 19 50 mm -20C 13 150 mm 38 mm | 38 mm 100 mm RH=90% RH=40% mm mm Surf. 1 Surf.…
solve this problem and dont reject it plzz
I need the answer quickly
3-55 The composite strip in Figure P3-55 is exposed to the convection environment at 300°C and h = 40 W/m². °C. The material properties are k₁ =20 W/m . °C, kB 1.2 W/m -°C, and kc = 0.5 W/m - °C. The strip is mounted on a plate main- tained at the constant temperature of 50°C. Calculate the heat transfer from the strip to plate per unit length of strip. Assume two-dimensional heat flow. Figure P3-55 - A B с Too = 300°C T = 50°C 6.0 cm 0.5 cm 1.5 cm 2.0 cm
The fin shown in Figure is insulated on the perimeter. The left end has a constant temperature of 100 °C. A positive heat flux of q = 5000 W/m² acts on the right end. Let Ky = 10 W/(m °C) and cross-sectional area A = 0.1 m2 Determine the temperatures at L/4, L/2, 3L/4, and L, where L = 0.8 m. 4-0.1 m T-100 C 5000 W/m
1- Microwave radiation is incident on one side of a planar wall with a heat conductivity coefficient k. (x=0) -D°b=(x)b leads to volumetric heating. While this surface is 9(W/m²) microwave radiation is fixed. kept at a constant temperature To, the other surface at x=L is very well insulated. Determine the temperature distribution T(x) in terms of x, L, k, qo and To.
A hot water pipe is used for domestic applications is insulated with a layer of calcium silicate. If the insulation is 25 mm thick and its inner and outer surfaces are maintained at Ts,1 = 800 K and Ts,2 = 400 K, respectively. The outside diameter is 0.12 m. Calculate the heat loss per unit length of the pipe. Given the thermal conductivity of calcium silicate insulation equals to 0.09 W/m.K.