The figure shows an elaborate pulley consisting of four small spheres and a uniform disk, all of which rotate together. Each sphere has a mass m = 4.46 kg, is held a distance of 0.29 m from the pulley's center by a massless spoke, and is small enough that it can be considered a point mass. When a block of mass M = 10.5 kg is attached as shown and released from rest, the ideal rope turns the pulley without slipping as the block descends. Calculate the block's speed v after falling a distance of 0.73 m, if the pulley's mass and radius are mp = 3.26 kg and R = 0.1 m. m mp V= M _________ m/s Record your numerical answer below, assuming three significant figures. Remember to include a "-" as necessary.

The figure shows an elaborate pulley consisting of four small spheres and a uniform disk, all of which rotate together. Each sphere has a mass m = 4.46 kg, is held a distance of 0.29 m from the pulley's center by a massless spoke, and is small enough that it can be considered a point mass. When a block of mass M = 10.5 kg is attached as shown and released from rest, the ideal rope turns the pulley without slipping as the block descends. Calculate the block's speed v after falling a distance of 0.73 m, if the pulley's mass and radius are mp = 3.26 kg and R = 0.1 m. m mp V= M _________ m/s Record your numerical answer below, assuming three significant figures. Remember to include a "-" as necessary.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

In the figure, two 5.40 kg blocks are connected by a massless string over a pulley of radius 2.40 cm and rotational inertia 7.40 × 10-4 kg-m². The string does not slip on the pulley; it is not known whether there is friction between the table and the sliding block; the pulley's axis is frictionless. When this system is released from rest, the pulley turns through 0.800 rad in 154 ms and the acceleration of the blocks is constant. What are (a) the magnitude of the pulley's angular acceleration, (b) the magnitude of either block's acceleration, (c) string tension T₁, and (d) string tension T₂? Assume free-fall acceleration to be equal to 9.81 m/s². (a) Number i (b) Number (c) Number i (d) Number i Units Units Units Units
An Atwood's machine consists of blocks of masses m1 = 13.0 kg and m2 = 16.0 kg attached by a cord running over a pulley as in the figure below. The pulley is a solid cylinder with mass M = 9.10 kg and radius r = 0.200 m. The block of mass m2 is allowed to drop, and the cord turns the pulley without slipping. (a) Why must the tension T2 be greater than the tension T1? (b) What is the acceleration of the system, assuming the pulley axis is frictionless? (Give the magnitude of a.) =________ m/s2 (c) Find the tensions T1 and T2. T1= ______N T2= _____N
You need to design an industrial turntable that is 60.0 cm in diameter and has a kinetic energy of 0.250 J when turning at 45.0 rpm (rev/min). (a) What must be the moment of inertia of the turntable about the rotation axis? (b) If your workshop makes this turntable in the shape of a uniform solid disk, what must be its mass?
A disk of mass 3.8 kg and radius 0.17 m starts at the bottom of a 25 degree incline. It'stranslational velocity is 16 m/s. How far along the incline does it roll before coming to astop?
A person with an axe to grind is using a whetstone. The whetstone is connected to a motor which keeps it rotating at 85 rev/min. The whetstone is a solid cylinder of made of a special type of stone of mass 45 kg and radius 20 cm. The heavy axeblade is being pressed onto the whetstone with a steady force of 25 N directed into the centre of the whetstone. Suddenly, the power to the motor is cut but the person maintains the force of the axe on the whetstone. The coefficient of kinetic friction between the axe and the stone is 0.60. The moment of inertia of a cylinder about it's centre of mass is I = ½MR2. (a) Calculate the torque of the frictional force on the wheel. (b) Calculate the total angle through which the wheel turns from the time the power goes off to the time the whetstone stops rotating. (c) How long does it take for the wheel to stop after the power outage?
A 34.0 kg wheel, essentially a thin hoop with radius 1.50 m, is rotating at 250 rev/min. It must be brought to a stop in 11 s. How much work must be done to stop it? What is the required average power?
An electric motor exerts a constant torque of τ=10N⋅mτ=10N⋅m on a grindstone mounted on its shaft; the moment of inertia of the grindstone is I=2.0kg⋅m2I=2.0kg⋅m2. If the system starts from rest, find the work done by the motor in 8.0 ss and the kinetic energy at the end of this time. What was the average power delivered by the motor? SOLUTION SET UP AND SOLVE We want to use W=τΔθW=τΔθ to find the total work done and then divide that by the time interval Δt=8.0sΔt=8.0s to find the average power (work per unit time). But first we need to find the total angle ΔθΔθ (in radians) through which the grindstone turns. The angular acceleration αα is constant, so we can use τ=Iατ=Iα to find αα and then apply the formulas for constant angular acceleration. The angular acceleration is α=τI=10N⋅m2.0kg⋅m2=5.0rad/s2α=τI=10N⋅m2.0kg⋅m2=5.0rad/s2 For constant angular acceleration, θ=θ0+ω0t+12αt2=0+0+12(5.0rad/s2)(8s)2=160radθ=θ0+ω0t+12αt2=0+0+12(5.0rad/s2)(8s)2=160rad The total work…
A wheel with a radius of 1.72 m and a mass of 0.230 kg rolls without sliding down a plane that is inclined at an angle φ = 26.97 °. g = 9,806 m / s². Calculate the kinetic energy of the wheel after the time 0.829 s if it has a moment of inertia 1.98 kg · m², starts from rest and a force acts on the wheel so that its angle of rotation varies with time according to θ (t) = 1.79 · t^3 rad.
A car is designed to get its energy from a rotating flywheel (solid disk) with a radius of 2.00 m and a mass of 400 kg. Before a trip, the flywheel is attached to an electric motor, which brings the flywheel's rotational speed up to 4500 rev/min. (a) Find the kinetic energy stored in the flywheel. (b) If the flywheel is to supply energy to the car as would a 20.0-hp motor, find the length of time the car could run before the flywheel would have to be brought back up to speed.
A way to test the tensile strength of a wire is to place a mass at the end of it and spin the mass with uniform circular motion. The speed at which the wire breaks is a measure of its strength. The maximum frequency of rotation before a certain wire breaks is 35.5 Hz. The wire is 50.5 cm long and has a mass of 0.656 kg. (a) Determine the speed with which the mass moves. (b) Calculate the centripetal force acting on the wire
A grindstone with a mass of 50 kg and radius 0.8 m maintains a constant rotation rate of 4.0 rev/s by a motor while a knife is pressed against the edge with a force of 5.0 N. The coefficient of kinetic friction between the grindstone and the blade is 0.8. What is the power provided by the motor to keep the grindstone at the constant rotation rate?
An Atwood's machine consists of blocks of masses m₁ = 13.0 kg and m₂ = 24.0 kg attached by a cord running over a pulley as in the figure below. The pulley is a solid cylinder with mass M = 7.60 kg and radius r = 0.200 m. The block of mass m., is allowed to drop, and the cord turns the pulley without slipping. M T2 Q (a) Why must the tension 7₂ be greater than the tension 7₁? This answer has not been graded yet. (b) What is the acceleration of the system, assuming the pulley axis is frictionless? (Give the magnitude of a.) m/s² (c) Find the tensions T, and T₂. T₁ = T2₂ =