4.Withtai yield strength of 393MP. JE the factor of safety is 4, calculate the allowable force EStrength of 210MPA. If the factor of safety is 4, calculate the key length.Note: fore circular shape weldingA = 1.414 zhrJ, = 2 nrF-045930

Given data: The given weld size from the figure is The radius of the weld is

The figure shows a welded-arm. The arm is welded using ! normal yield strength of 393MPa. If the factor of safety is 4, calculate the allowable force F. If the torque is transmitted via a key 10x8 mm. The key material is ST 37 with normal yield With strength of 210OMPA. If the factor of safety is 4, calculate the key length. Note: fore circular shape welding

The figure shows a welded-arm. The arm is welded using ! normal yield strength of 393MPa. If the factor of safety is 4, calculate the allowable force F. If the torque is transmitted via a key 10x8 mm. The key material is ST 37 with normal yield With strength of 210OMPA. If the factor of safety is 4, calculate the key length. Note: fore circular shape welding

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate external support reactions, forces of internal joints and draw FBD of assembly
I keep getting this one wrong. For T1, I did 370/cos(30) = 427.24 lb tension , and -427.24 x cos(30)= -370. I also tried T1=820, and T2=-710.14, which was not correct as well. Thank you for your help on these two parts
Please help ASAP. Help for parts A-B will upload for the other part. Provide Free Body Diagram, labeled with appropriate quantities to better understand. Also solve. Thank you.
Give me correct answers please
Mechanical design
19. The Knuckle Joint is made from SAE 1020 Steel having an allowable tensile strength of 15,000 psi and an allowable shear strength of 7500 psi. The axial load is 1 ton (recall, 1 ton = 2205 lb). Yoke Pin Rod -A The dimensions are as follows: D-0.652 in d-0.652 in c = 0.66 in b = 0.33 in m = 1.306 in e = 0.505 in Determine: a) Tensile stress (psi) at section A-A b) Factor of safety for a) c) Shearing stress (psi) in the pin d) Factor of safety for b) e) Bearing stress (psi) between the pin and the rod f) Factor of safety for e) g) Bearing stress (psi) between the pin and the yoke h) Factor of safety for g) i) Tensile stress (psi) across the hole in the rod j) Factor of safety for i) k) Tensile stress (psi) across the hole in the yoke 1) Factor of safety for k)
Te - Effective throat thickness well in mm = 6 sin45° Consider the following drawing in which plate 1 is welded onto plate 2 as shown for tensile and shear loading. The plates are fillet welded with a weld thickness of 6 mm as shown for a length of 150 mm. The plates have an ultimate strength of 275 MPa and the welding was done with F70 welding electrodes, which possesses an ultimate strength of 483 MPa. Consider a partial factor of safety of 1.7 for the welded joint and determine the design strength of the weld joint, both in tension (Tdw) and in shear (Vdw) due to the forces acting on it. a) Determine the design strength of the following weld in tension ( ) due to vertical forces. b) Determine the design strength of the weld in shear ( ) due to horizontal forces. Attached pic is shear equation for calculation Tension equation for calculation is: Tdw = FyLwte /Ymw
The figure illustrates the connection of a steel cylinder head to a grade 30 cast-iron pressure vessel using N bolts. A confined gasket seal has an effective sealing diameter D. The cylinder stores gas at a maximum pressure pg. For the specifications given in the table for the specific problem assigned, select a suitable bolt length from the preferred sizes in Table A–17, then determine the yielding factor of safety np, the load factor nL, and the joint separation factor n0. See problem number 8-36, and please use the FEA exponential curve-fit for member stiffness.
Determine the safe tensile load for bolts of (a) M 17 and (b) M 26. Assume that the bolts are not initially stressed and take the safe tensile stress as 305 MPa
Data: r=0.25 inch, d=0.4 pig and h=0.5 inch, wi=2.5 inch and w= 1.5 inch.The forces fluctuate between a tension of 14 Kips and a compression of 5 Kips. It is made of AISI 1018 CD. steel.The connecting element in the figure is failing. What is the most critical point and give recommendations to improve the situation.