The figure shows a shaft mounted in bearings at A and D and having pulleys at B and C. The forces shown acting on the pulley surfaces represent the belt tensions. The shaft is to be made of AISI 1035 CD steel. Using distortion-energy theory with a design factor of 2, determine the minimum shaft diameter to avoid yielding.

Q: The cold-drawn steel shaft has an ultimate strength of 1350 MPa, yield strength of 1200 MPa, and…

A:

Q: Solid circular shaft is under bending and torsion loadings. Uniaxial tensile yield strength of the…

A:

Q: Compute the torsional shear stress in a circular shaft with a diameter of 50 mm that is subjected to…

A: GivenT=800 Nmd=50mm=0.05 mFormulaσT=16Tπd3

Q: Consider the compound shaft KC which is composed of a 1200mm long solid rod fitted snuggly into an…

A:

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A: The power available, P = 25 hp The speed of motor, N = 1800 rpm The diameter, d2 = 1.25 in The…

Q: Solve the following problem Two designs for a shaft are being considered. Both have an outside…

A: Shear stress for solid shaft is given as  τ=16*Tπ*d3=16*325*1000π*703=4.825 MPa Shear stress for…

Q: Please give a detailed explanation with a free body-diagram.

A: To provide a detailed explanation along with a free body diagram (FBD) for determining the reaction…

Q: An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter…

A:

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A: The power available, P = 25 hp The speed of motor, N = 1800 rpm The diameter, d2 = 1.25 in The…

Q: what is the Moment at point A

A: First find the moment produce by given torque as follows.

Q: Bearing stress 5. Please provide proper discussion and illustration also complete solution and…

A: given; transmitting force(F)=50KN                                     =50*103Nshear stress on…

Q: The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid…

A: The power supply by the motor is The speed of the motor is The diameter of shafts 1 and 2 is The…

Q: The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley…

A: diameter of pulley (d) = 110 mm  no of belt = n = 2 groove angle =  2β = 45° = β = 22.5° power…

Q: Q1 The rotating solid steel shaft is simply supported by bearings A and B, the gear has 500-mm pitch…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: A stepped shaft has dimensions of D = 2 in., d = 1 in., and r = 0.1 in. It is machined from AISI…

A: given data :D=1.2 inchd=1 inchr=0.03inso=100ksiSY=80ksiassumption the shaft is manufactureis as…

Q: Figure below shows a portion of a pump that is gear-driven at uniform load and speed. The 25 mm…

A:

Q: Determine the allowable value of the torque, T, which can be applied to the solid circular shaft…

A:

Q: The chain drive is mounted in the center for the system shown in figure.It can transmit 15 hp at a…

A:

Q: A steel cable is supporting a load of F = 9800 lb and is wrapped around a drum attached to gear A as…

A:

Q: The end gear (closest to the journal bearing at A) is subjected to the loading shown in the figure.…

A: Given: The yields strength of material = 80 MPa

Q: The figure shows a shaft carrying three gears that rotates at 1150 rpm. Gear A delivers power =10kw…

A: Given, Gear A deliver 10KN Gear C deliver 15KN A shaft carrying 3 gears that rotates at 1150 rpm…

Q: 25m (a) The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer…

A: Given data:- Inner diameter = 40 mm Outer diameter = 50 mm Torque = 2.5 kN-m Moment = 3.6 kN-m Find…

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A:

Q: The membrane analogy does not apply to the hollow cross-sections considered in Chapter 3…

A: In terms of features, appearance, and structural behaviour, square hollow sections (SHS) are a…

Q: a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa,…

A: for solution refer below images.

Q: 42, The static deflection at the center of the steel shaft in Fig. 3-53 is equal to 0.35 mm. Find…

A: Given: The static deflection of shaft, x= 0.36 mm

Q: m. Design a cast Iron flange coupling for the shaft. The allowable stresses are Shear stress for the…

A:

Q: Pravinbhai

A: Step 1: Step 2: Step 3: Step 4:

Q: Gear shaft ABCDE is subjected to the torques shown in the figure. Find the internal torque in each…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.