The figure shows a portion of a plate cam used in the design of a control mechanism. The motion of pin Pin the fixed slot of the plate cam is controlled by the vertical guide A, which travels horizontally at aconstant speed af 9 in./sec over the central sinusoidal partion of the slat. Determine the normal component af acceleration when the pin is at the position x = 1 in. Set h = 4 in. and d = 5 in.h(1- cos[7x/d])2hAdAnswer: an =Jin./secthe tolerance is +/-2%Click if you would like to Show Work for this question: Open Show Vork

Given data: Write the given equation.

The figure shows a portion of a plate cam used in the design of a control mechanism. The motion of pin Pin the fixed slot of the plate cam is controlled by the vertical quide A, which travels horizontally at a constant speed of 9 in./sec over the central sinusoidal pertion of the slot. Determine the normal component af acceleration when the pin is at the position x=1 in. Set h=4 in. and d= 5 in. h(1- cos[7x/d]) 2h Answer: linsec? the tolerance is +/-2% Click if you would like to Show Work for this question: Onen Show Work

The figure shows a portion of a plate cam used in the design of a control mechanism. The motion of pin Pin the fixed slot of the plate cam is controlled by the vertical quide A, which travels horizontally at a constant speed of 9 in./sec over the central sinusoidal pertion of the slot. Determine the normal component af acceleration when the pin is at the position x=1 in. Set h=4 in. and d= 5 in. h(1- cos[7x/d]) 2h Answer: linsec? the tolerance is +/-2% Click if you would like to Show Work for this question: Onen Show Work

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q/ The dimensions of the links for mechanism as shown beside are: OA = 12 cm AC= 47 cm AB= 60 cm 55cm CD= 55 cm The link OA rotates at 942.5 rad/min and is pinned at A to road AB. The point C in the road is guided in circular path with D at center of DC as a radius. Determine the velocity of CD, sliding E and acceleration of E 22cm 60cm
5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angular velocity W and angular acceleration a (both counterclockwise). 4) if W = 4.0 rad/s and a = 6.3 rad/s2, length I = 1.5 m, and angle 0= 36°, what is the magnitude of the angular velocity of link AB? Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper unit. 0.5 m 0, a B Your Answer: Answer units
Solve 4,5,6
For the Mechanism shown, find the acceleration of the slider link4 using Vector loop method. Assume r3=1 cm. Y B KE 13 =90°. 00₂= 10 rad/s CCW (constant) X Hand written plz a
The elements of a power hacksaw are shown in Figure 2. The saw blade ismounted in a frame that slides along the horizontal guide. If the motor turns the flywheel at a constant counter-clockwise speed of 60 r.p.m. Make use of vector diagram to calculate: the acceleration of the blade for the position where angle ? = 90o The corresponding angular acceleration of the link AB.
Q1A = 12 inches, Q102 = 5 inches. The Crank Q1A rotates uniformly CCW at a speed of 75 RPM. Find the absolute linear acceleration of Body #3.
In the figure, Pulley A, rotating at 20 rad/s, controls the motion of Pulley B. The motor of pulley A is cut off, and friction eventually brings the pulleys to a stop with an angular acceleration of α = -2.5t rad/s2. If there is no slippage, determine: a. The angular velocity of B with respect to time b. The angular displacement of B during the deceleration c. The acceleration of point C with respect to time
The cam rotates at the angular velocity of @ = 10rad / s . R= 50mm , 140 = 20mm . Calculate the velocity V2 of link 2, when ø = 45° , and 90°, respectively. %3D B R
Find the angular velocity and angular acceleration of the wheel according to the values given in the motion of the system seen at this position.
What is the solution
Please accept
Parvinbhai