The figure, Fig.Q.4(b), shows a rigid-jointed plane frame subjected to the' load condition shown in the figure. Determine the horizontal deflection of C and slope at A of the frame by using the principle of virtual work. Assume that the members of the frame have same flexural rigidity, El. 200 N/m B 10 m 10 m

The figure, Fig.Q.4(b), shows a rigid-jointed plane frame subjected to the' load condition shown in the figure. Determine the horizontal deflection of C and slope at A of the frame by using the principle of virtual work. Assume that the members of the frame have same flexural rigidity, El. 200 N/m B 10 m 10 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3. (a) Use the moment-area method to determine deflections at C of the beam shown in the figure. BMD…

A: E = 200 GPa = 200 x 103 N/mm2 [we are only suppose to answer 1 question. Kindly post other question…

Q: E = 70 GPa. the deflection 20-mm diameter 0.4 m 0.5 m 60-mm diamete

Q: 180 kN 15 kN/m B D -5 m- -5 m- -4 m- El = constant E = 70 GPa I = 2,340 (106) mmª %3D

Q: We are given the beam shown in Fig. 4. The moment of inertia of member AB is two times bigger than…

A: E = 5000 ksi = 720000.00 ksf I = 1000 in4 = 0.0482 ft4

Q: A 4-meter cantilever beam supports a uniformly distributed load of w=25 kN/m at half of its span;…

A: Determinea. Deflection at the free end in terms of E. b. Slope at the free end in terms of E.

Q: Using double integration method

A: Given Data E = 70 GPa = 70 × 103 N/mm2 I = 95 × 106 mm4 Determine the maximum deflection in the…

Q: F1.5 m→–1.5 m→- 2.1 m A В D Pj = 400 kN 2.4 m P2 = 360 kN %3D F 0.6 m E

Q: For the given problem, the intensity of the distributed load varies linearly from 0 to Wo = 14kN/m.…

A: To find a. Equation of elastic curve. b. Location of maximum deflection and maximum deflection.

Q: Problem 13: Determine the horizontal deflection at point D for the frame as shown in figure by…

A: Given : E = 2 X 105 N/mm2 I = 8 X 108 This is a problem of structure where we are asked to…

Q: 1.5 k/ft 30 k A D В C -6 ft 4 ft- +5 ft- El = constant

A: Given:- A simply supported beam is given with pin support at point A and roller support at point D.…

Q: A flat circular plate of radius R and constant flexural rigidity D is uniformly loaded on one face…

A: Given: The radius of a flat circular plate is R. The flexural rigidity is D. To Determine: Show…

Q: 2. Determine the vertical deflection of joint B and the horizontal movement of the support D in the…

Q: The simply supported beam ABC in Fig. (a) carries a concentrated load of 300 N as shown. Det…

A: Calculation of Reactions: ∑M at A =0RC×3-200×2=0RC=4003=133.33kN∑V= 0RA+RC=200RA=200-133.33=66.67kN…

Q: Example: The simply supported beam shown P=6KN. Determine the maximum is subjected to the…

Q: A W = 500 N R = 150 mm 250 mm Figure Q3

A: from the figure,using equilibrium conditionmoment at the supportMA=w150 N-mmtotal strain…

Question

(b) The figure, Fig.Q.4(b), shows a rigid-jointed plane frame subjected to the load
condition shownm in the figure. Determine the horizontal deflection of C and slope at A
of the frame by using the principle of virtual work. Assume that the members of the
frame have same flexural rigidity, EI.
200 N/m
B
10 m
10 m
Fig.Q.4(b)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

6. Given the beam loaded as shown, determine the deflection at the midspan. Use Conjugate Beam Method. 270 kN 45 kN/m A C 3 m 3 m- - 3 m El = constant 200 GPa I = 1665x106mm4 E %3D
3. The beam shown below has a Young’s modulus of 50 GPa and has a square cross-section of side1 cm. Determine the following using the second-order integration method:(a) Bending moment M(x) along the length of the beam.(b) The slope of the beam θ(x).(c) The deflection of the beam v(x).(d) Slope of the beam at support θB
3. By using Double Integration Method, Determine the deflection at the free end of the beam shown A 5m 300 kN-m B L = 10 m El= constant E = 200 GPa 5 m 60 kN
Use integration method
Consider the cantilever beam in the figure,subject to a concentrated force P = 20kip at Band a concentrated moment Mo = 100k-ft at C.Knowing that a = 5ft, use the conjugate beammethod to calculate the following in terms ofgeneric E and I:(a) The slope of point C(b)The deflection of point B
Q. 4 Determine the slope at the supports for the beam shown below. Also, determine the deflections at B and C. 10 ft I 40 k B 60 k 10 ft 21 E = constant = 29,000 ksi I = 1,000 in.4 10 ft I Q. 4
Please solve part A
Compute the vertical and horizontal component of the deflection at C of the frame in the following figure using the method of virtual force. The direction of uniformly distributed loading is "→". Take E=200GPa, I=240(106)mm4.
Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A concentrated load of P = 16 kips is applied to the free end of bronze rod (3). Determine the magnitude of the deflection of rod end D after the temperature of all rods has increased by 125°F. Use the following dimensions and properties: a = 2.8 ft, b = 6.3 ft. Rod (1): d₁ = 0.90 in., L₁ = 11 ft, E₁ = 15,200 ksi, α₁ = 12.20 × 10-6/°F. Rod (2): d₂ = 0.80 in., L₂ = 9 ft, E2 = 28,000 ksi, a₂ = 9.60 × 10-6/F. Rod (3): d3 = 1.25 in., L3 = 5 ft, E3 = 15,200 ksi, a3 = 12.20 x 10-6/°F. VD = i L in. (1) A a L3 B (3) D b Rigid bar L2
1. Use Virtual Work Method to answer the questions below considering the truss shown in the figure. Assume A = 1200 mm?, E = 200 GPa and a = 12 x 106 / °C %3D %3D c. Vertical displacement of joint A in mm due to external force only. Put negative sign if its downward. I d. Vertical displacement of joint A in mm due to -100 °C change in temperature in members AE and ED. Don't add deflection due to external loads or fabrication error. Put negative sign if its downward. D E 4.1m A ' 3.6 kN 5.4 kN 4.1m 4.1m
A beam is subjected to a bending moment, as shown in the figure below, where point B is assumed to be an internal connection, point C is assumed to be a rolling bearing, and the flexural stiffness of the beam section is a constant EI:(a) Use the Conjugate Beam Method to find the slope of point B after deformation.(b) Same as above, try to find the vertical displacement of point D.Tip: The left and right slopes of point B may be different
Part d) Vertical defection at Point c Use the principle of virtual work to determine the vertical deflection at Point C. ( the positive direction of a vertical deflection points upwards )