The figure below shows a slidewire generator with motional emf E, when the wire at A slides across the top and bottom rails at constant velocity vn- |৫ A B HINT (a) When the wire reaches B so that the area enclosed by the circuit is doubled, determine the ratio of the new emf to the original emf, (b) If the wire's speed is doubled so that v = 2vg determine the ratio x! x

The figure below shows a slidewire generator with motional emf E, when the wire at A slides across the top and bottom rails at constant velocity vn- |৫ A B HINT (a) When the wire reaches B so that the area enclosed by the circuit is doubled, determine the ratio of the new emf to the original emf, (b) If the wire's speed is doubled so that v = 2vg determine the ratio x! x

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A transformer is to be used to provide power for a computer disk drive that needs 5.6 V (rms) instead of the 120 V (rms) from the wall outlet. The number of turns in the primary is 420, and it delivers 500 mA (the secondary current) at an output voltage of 5.6 V (rms). (a) Should the transformer have more turns in the secondary compared to the primary, or fewer turns? O There should be more turns in the secondary. O There should be fewer turns in the secondary. (b) Find the current in the primary. (c) Find the number of turns in the secondary. turns
An RL circuit consists of a switch, an emf source E,, a 3.0 ka resistor, and a 1.0H inductor. If the potential across the resistor is 15.0 V 8.0 ms after the switch is closed, find the source emf, E..
(a) What is the characteristic time constant of a 23.3 mH inductor that has a resistance of 4.09 Ω? ms(b) If it is connected to a 12.0 V battery, what is the current after 12.5 ms? A
A V = 86-V source is connected in series with an R = 1.8-kΩ resistor and an L = 26-H inductor and the current is allowed to reach maximum. At time t = 0 a switch is thrown that disconnects the voltage source but leaves the resistor and the inductor connected in their own circuit. 1) How much time, in milliseconds, is needed for the current in the circuit to drop to 12 % of its value at t = 0? 2) How much energy, in millijoules, does the circuit dissipate during that time?
A series RLC circuit consist of L = 1H, C = 0.05 F and an unknown resistance R. If the applied voltage lags the current by an angle of 63.43º, find the value of R. Assume w = 4 rad/s.
In a home stereo system, low sound frequencies are handled by large “woofer” speakers, and high frequencies by smaller “tweeter” speakers. For the best sound reproduction, low-frequency currents from the amplifier should not reach the tweeter. One way to do this is to place a capacitor in series with the 8.0 Ω resistance of the tweeter; one then has an RLC circuit with no inductor L (that is, an RLC circuit with L = 0). What value of C should be chosen so that the current through the tweeter at 200 Hz is half its value at very high frequencies?
The current in the RL circuit shown below reaches one-fourth its maximum value in 2.75 ms after the switch s, is thrown. R (a) Determine the time constant of the circuit (in ms). ms (b) Determine the resistance of the circuit (in 0) if L = 200 mH.
How would I solve this DC Circuits question?
A circuit consists of 18 volts battery, a 72 mH inductor and two 50 ohms resistors connected in parallel. a) Find the characteristic time constant for the circuit. b) What is the current in the circuit at two characteristic time intervals after the switch is closed? c) A long-time-interval after the switch is closed L R R ww
(a) What is the characteristic time constant of a 25.2 mH inductor that has a resistance of 4.02 N? ms (b) If it is connected to a 12.0 V battery, what is the current after 12.5 ms? A
In a home stereo system, low sound frequencies are handled by large "woofer" speakers, and high frequencies by smaller "tweeter" speakers. For the best sound reproduction, low-frequency currents from the amplifier should not reach the tweeter. One way to do this is to place a capacitor in series with the 9.0 Ω resistance of the tweeter; one then has an RLC circuit with no inductor L (that is, an RLC circuit with L = 0). What value of C should be chosen so that the current through the tweeter at 200 Hz is half its value at very high frequencies?
(L11) At t = 0 s, a 3.53E-3 H inductor carries a 5.03 A current flowing from a to b, as shown in the figure. The current then decreases at a constant rate until it becomes zero at t = 4.10 s. The voltage is measured to be Va at point a and V₁ at point b. What is the voltage difference Va-Vb between t = 0s and t = 4.10 s (in V; answer the sign and magnitude)? a فیقققق L elle I b