The figure below shows a metal plate with a width of w 2 cm and a thickness of t = 0.1 cm. An electric current I= 20A is applied to it and placed in a magnetic field B in the direction shown in the figure. When the applied magnetic field is 2 tesla, the resulting Hall voltage of 4.28 V. Based on the above, determine the electron drift velocity (Vd)!

The figure below shows a metal plate with a width of w 2 cm and a thickness of t = 0.1 cm. An electric current I= 20A is applied to it and placed in a magnetic field B in the direction shown in the figure. When the applied magnetic field is 2 tesla, the resulting Hall voltage of 4.28 V. Based on the above, determine the electron drift velocity (Vd)!

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

It is proposed to use the Earth's magnetic field to turn a coil that is carrying an electric current. What is the maximum torque that can be produced in a rectangular coil of sides 4-m by 3-m, where the Earths magnetic field has a strength of 31 micro-tesla, and the current in the coil is 6 amperes. Write your answer in milli-Nm.
A square shaped wire loop of sides D= 5L is placed in a magnetic field as shown in the figure. r is the radial distance from the given axis and tis the time coordinate. (The bottom and top sides are at r= Land r=L+D, respectively.) The magnitude of the magnetic field is given by 8r.1)=(9) V/s and the its direction is shown in the figure. The resistance of the square shaped wire is 4 2. What is the magnitude (in units of A) and the direction of the induced current on the the loop at time 68? 9.26, clockwise 9.26, counter-clockwise O54.00, clockwise 112.50, counter-clockwise 112.50, clockwise L D OB r D
Suppose you wish to measure the current in a wire. You have a device that can measure the strength of the magnetic field produced by the wire, but the device does not directly measure the current. If the device is place 1.32m away from the wire, and the magnetic field strength is 0.93μT, what is the current running through the wire in Amps? Note: It is understood that the unit of your answer is in A, however do not explicitly include units in your answer. Enter only a number. If you do enter a unit, your answer will be counted wrong.
The Hall effect can be used to determine the density of mobile electrons in a conductor. A thin strip of the material being investigated is immersed in a magnetic field and oriented so that its surface is perpendicular to the field. In a particular measurement, the magnetic field strength was 0.723 T, the strip was 0.107 mm thick, the current along the strip was 2.83 A, and the Hall voltage between the strip's edges was 2.73 mV. Find the density n of mobile electrons in the material. The elementary charge is 1.602 x 10-1° C. n = -3 m
Please type instead of hand writting
The straight wire that has been bent into a perfect circle has been placed in a perpendicular magnetic field has a length of 30.0 cm. The magnetic field is changing at a rate of 13 T/s. If the resistance of the wire loop is 3.6 Ω, the electric current in the wire will be:
Consider the following:A uniform magnetic field B= -0.033TK is present in a region of space, as shown in the figure. There is also a uniform electric field in this region of space. A proton with a. constant velocity Vo=74 m/s i passes through the region without deflection. What is the direction of the electric field in the region?
An electromagnetic rail gun uses magnetic forces to launch projectiles. (Figure 1) shows a 10-cm-long, 12 g metal wire that can slide without friction along 1.0-m-long horizontal rails. The rails are connected to a 300 V source, and a 0.10 T magnetic field fills the space between the rails. Each rail has linear resistivity λ = 0.10 /m, which means that the resistance is A multiplied by the length of rail through which current flows. Assume that the sliding wire and the left end, where the voltage source is, have zero resistance. The wire is initially placed at x0 = 30 cm, then the switch is closed. Figure Part A X X X x 10 cm х X X × 0.10 T X X + X X 300 V × ✗ ✗ X X ✗ ☑ × × × x What is the wire's speed as it leaves the rails? 1 of 1
kg. Consider the mass spectrometer shown schematically in the figure below. The electric field between the plates of the velocity selector is 945 V/m, and the magnetic fields in both the velocity selector and the deflection chamber have magnitudes of 0.900 T. Calculate the radius r of the path for a singly charged ion with mass m = 2.06 x 10-26 mm X x P x r Bo, in X x X X X X Photographic plate Bin Velocity selector x x x x + + 1₂ E x x x x X--- --- V X X x || 9 XA I x I x X X x x x X X
A square loop consists of a single turn with a resistance of 5.00 . The loop has an area of 200 cm², and has a uniform magnetic field passing through it that is directed out of the page. The loop contains a 12-volt battery, connected as shown in the figure below. 12 V (a) At the instant shown in the figure, there is no net current in the loop. At what rate is the magnitude of the magnetic field changing? T/S (b) If the polarity of the battery was reversed, and the magnetic field was still changing at the rate you calculated above, what would the magnitude of the net current through the loop be? A
loop. The magnetic field in this case is A vertically oriented square loop of copper wire falls from rest in a region in which the field B is horizontal, uniform, and perpendicular to the plane of the loop, into a field- free region, see (Figure 1). The side length of the loop is s and the wire diameter is d. The resistivity of copper is PR and the density of copper is pm. If the loop reaches its terminal speed while its upper segment is still in the magnetic-field region, find an expression for the terminal speed. Part I Find the emf. Express your answer in terms of the variables s, B, and v. ▸ View Available Hint(s) E = Ο ΑΣΦ Submit Figure Square loop of copper wire. Above this line: Buniform and horizontal Below this line: B=0 s = side length X X 1 of 1 X X X XBX X dwire diameter ↑ s = side length Part J Complete previous part(s) Part K Complete previous part(s) Part L Complete previous part(s) Part M Complete previous part(s) Part N Complete previous part(s) EVALUATE Uterminal Part…
Is my answer to this question correct?