The extruded plastic shape will be subjected to an internal shear force of V=385 lb. Dimensions of the cross section are b- 1.2 in., d- 2.4 in., c-1.6 in., and t-0.13 in. Determine: (a) the magnitude of the horizontal shear stress at points A and B. (b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yc- 0.8 in. below the z centroidal axis. (c) the magnitude of the maximum horizontal shear stress in the extrusion.

The extruded plastic shape will be subjected to an internal shear force of V=385 lb. Dimensions of the cross section are b- 1.2 in., d- 2.4 in., c-1.6 in., and t-0.13 in. Determine: (a) the magnitude of the horizontal shear stress at points A and B. (b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yc- 0.8 in. below the z centroidal axis. (c) the magnitude of the maximum horizontal shear stress in the extrusion.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: The extruded plastic shape will be subjected to an internal shear force of V = 395 lb. Dimensions of…

A: The extruded plastic shape which is supported to the an interior force are given in the question.…

Q: The extruded plastic shape will be subjected to an internal shear force of V = 325 lb. Dimensions of…

A: The given data is shown below: V=325 lbb=1.3 in.d=2.6 in.c=1.8 in.t=0.11 in.

Q: Consider a rectangular cross section with internal transverse shear. Which of the following is…

A: 1.Answer The magnitude of the transverse shear stress is ZERO at the top and bottom fibers of the…

Q: Using the cracked transformed section with b = 250 mm and d= 500 mm and j= 0.8501, If M = 150 KN.m…

A: Given :- Width of the transformed section (b) = 250 mm Depth of the section (d) = 500 mm j= 0.8501…

Q: The extruded plastic shape will be subjected to an internal shear force of V=260 lb. Dimensions of…

Q: A bar of the rectangular cross-section is 100mm thick by 50mm broad and carries an axial compressive…

Q: The extruded plastic shape will be subjected to an internal shear force of V = 350 lb. Dimensions of…

Q: The extruded plastic shape will be subjected to an internal shear force of V = 305 lb. Dimensions of…

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

Q: The extruded plastic shape will be subjected to an internal shear force of V = 305 lb. Dimensions of…

A: Given:- The magnitude of the shear force = V = 305 lb The dimensions of the cross-section are:- b =…

Q: ☐please work out the compliance matrix for the linear isotropic elastic plane stress and plane…

Q: The extruded plastic shape has dimensions of D = 32 mm, d = 30 mm, a = 89 mm, and t = 7 mm. (a)…

Q: Situation 2: A circular hole is to be punched in a plate that has a shear strength of 280 MPa. The…

A: Compressive stress for the punch (σ) = 350 MPa Shear strength (τ) = 280 MPa Determinea. Maximum…

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A: to find - absolute maximum shear stress from given principal stresses.

Q: 1. Mohr's Circle. Determine the radius of the circle (R) and the coordinates for the center of the…

A: X axis represents normal stress and y axis represents Shear stress.

Q: The extruded plastic shape will be subjected to an internal shear force of V = 225 Ib. Dimensions of…

A: First find the centroidal distance, y¯ y¯ = ∑Ay¯∑A =…

Q: the magnitude of the horizontal shear stress at points A and B. the magnitude of the horizontal…

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A: This question is related to the Strength of Material.

Q: Determine the value of maximum shear stress Maximum principal stress-25.92 MPa Minimum principal…

A: Given data in question Maximum and minimum principal stress To find out Maximum shear stress

Q: 2. In the structure below, the vertical bar A has a modulus of elasticity of 210 GPa, a length of…

Q: 9.6 Determine the stresses in the two segments of the bar shown. Segment A has a diameter of 1 in.…

A: FOR SEGMENT A DIA = 1.25 IN. LOAD= 10 KIP FOR SEGMENT B CROSS SECTION = 2IN * 2IN LOAD =22 KIP

Q: The extruded plastic shape will be subjected to an internal shear force of V = 395 lb. Dimensions of…

A: Given data: V = 395 lb b = 1.0 in., d = 2.0 in., C= 1.4 in., and t= 0.10 in. It is asked to…

Q: The extruded plastic shape will be subjected to an internal shear force of V = 370 Ib. Dimensions of…

A: Given,The shear force is,V=370 lbThe dimensions of the cross-section area are,b=1.7 ind=3.4 inc=2.3…

Q: 4 in. 4 in. 2 in. 1 in. P 1.8 During the tension test, the wooden specimen on the left is subjected…

Q: For the state of stress shown in the figure below: (CLO 3 a. Draw Mohr's Circle. b. Show x/y planes,…

A: Question is based on the state stress . Stress in x,y direction and shear stress is given in the…

Q: The extruded plastic shape will be subjected to an internal shear force of V= 395 lb. Dimensions of…

Q: The extruded plastic shape will be subjected to an internal shear force of V = 215 lb. Dimensions of…

Q: Determine the force required to produce stress of 20 N/m2 on cross sectional area of 5 m2

A: Stress = 20N/m2 Cross-sectional area = 5m2 It has been asked in the question to determine the…

Q: X Incorrect "he extruded plastic shape will be subjected to an internal shear force of V = 380 lb.…

A: To solve this question we will first find the neutral axis distance. Then we will calculate the…

Q: member with 0.2-in. wall thickness (3), cach supports an axial tensile load of 5 ki (a) Determine…

A: for easier calculations first all units are converted in to SI and for simplicity again convered…

Q: The extruded plastic shape will be subjected to an internal shear force of V- 265 lb. Dimensions of…

Q: Please show intermediate steps including free body diagrams, equations used, problem setup etc. so…

Q: Using the equations for determination of stress at a point, calculate the value for the maximum…

Q: (a) the magnitude of the horizontal shear stress at points A and B. (b) the magnitude of the…

Q: A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V determine…

Q: The extruded plastic shape will be subjected to an internal shear force of V = 350 lb. Dimensions…

Q: The extruded plastic shape will be subjected to an internal shear force of V = 395 lb. Dimensions of…

A: To solve this question, first we need to have the values of moment of area. So we will calculate…

Q: The extruded plastic shape will be subjected to an internal shear force of V = 315 lb. Dimensions of…

Concept explainers

Solid Mechanics

Engineering mechanics is a branch of science that deals with forces causing bulk motion in bodies and the effect that these forces cause on the bodies. Engineering mechanics does not deal with the internal changes that occur on account of these external forces. The internal effects in a body or a material under the action of external forces are studied in a new branch of science called solid mechanics, the strength of materials, or the mechanical behavior of engineering materials.

Question

The extruded plastic shape will be subjected to an internal shear force of V=385 lb. Dimensions of the cross section are b- 1.2 in., d=
2.4 in., c 1.6 in., and t = 0.13 in. Determine:
(a) the magnitude of the horizontal shear stress at points A and B.
(b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yc=0.8 in. below the z centroidal axis.
(c) the magnitude of the maximum horizontal shear stress in the extrusion.
(typ.)
B
Yc
Answer:
(a) TA
psi
TB
psi
(b) Tc =
psi
(c) Tmax
psi

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Due to loading, the plate is deformed into the dashed shape shown in the figure. Assume a = 39 in., b= 33 in., δ1= 0.1625 in., δ2= 0.1 in. Determine the average normal strain along the side AB?in micro rad And answer in right and clear way Determine the average shear strain in the plate at A relative to the horizontal and vertical axes?
1.61.The state of stress at a point relative to an x, y, z coordinate system is given by 12 4 2 4 -8 -1 MPа -1 6. Calculate the maximum shearing stress at the point.
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) Op1 = 2780 psi, Op2 = -2440 psi, op3 = 0 (b) op1 = 58 MPa, op2 = 35 MPa, Op3 = 0 Answer: (a) Tabs max= psi (b) Tabs max = MPa
The extruded plastic shape will be subjected to an internal shear force of V= 315 lb. Dimensions of the cross section are b = 1.3in, d= 2.6 in, c= 18 in, and t= 0.11 in. Determine: (a) the magnitude of the horizontal shear stress at points A and B. (b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yc = 0.9 in. below the z centroidal axis. (c) the magnitude of the maximum horizontal shear stress in the extrusion. (tуp.) B' d Ус Answer: (a) TA = psi Tg = psi (b) Tc =1 psi (c) Tmax psi
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) Op1 = 3300 psi, Op2 = -1830 psi, Op3 = 0 (b) 0p1 = 44 MPa, Op2 = 29 MPa, Op3 = 0 Answer: (a) Tabs max psi (b) Tabs max= MPa
Your answer is partially correct. Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) op1 = 2780 psi, o,2 = -2440 psi, op3 = 0 (b) Op1 = 58 MPa, Op2 = 35 MPa, Op3 = 0 Answer: (a) Tabs max psi 1390 (b) Tabs max MPa 29
answer quickly
Question 8 of 10 View Policies Current Attempt in Progress HO D d The extruded plastic shape has dimensions of D = 37 mm, d = 35 mm, a = 99 mm, and t = 7 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 365 N. (b) If the allowable shear stress for the plastic material is 800 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? N Answer: dik a - / 10 E ||| :