The equivalent circuit of a 22KVA, 11700/450 V. 60Hz, single-phase loaded transformer when referred to its low-voltage side is given. Find the copper and the core losses of this transformer under this loading conditions. = 37.037/-25.84 A Answers: Pcu- ESKO 2.0 +2.250 w j6.1 Ko Watt, and Pare Vs = 220/0 V Watt,

The equivalent circuit of a 22KVA, 11700/450 V. 60Hz, single-phase loaded transformer when referred to its low-voltage side is given. Find the copper and the core losses of this transformer under this loading conditions. = 37.037/-25.84 A Answers: Pcu- ESKO 2.0 +2.250 w j6.1 Ko Watt, and Pare Vs = 220/0 V Watt,

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

During the load test of single-phase transformer, when the secondary terminal voltage increases, the regulation of the transformer will ................?(complete)
A 1100/170V, 50 HZ, 1-phase transformer with cross sectional area of the core is 30 cm? and maximum flux density is 1.5 wb/m2. The number of turns required on the LT side will be
Q6 Complete the answer : If connected .................... to the transformer changes, copper loss varies.
Q2/A/ What are the conditions for satisfying parallel operation of single phase transformer? Deduce an expression for the load shared by the two transformers in parallel when the transformers have equal voltage ratio? Prove your answer. B/ A 50 KVA, 2300/230 V, 60 11z transformer has a high voltage winding resistance of 0.650 and a low-voltage winding resistance of 0.0065 2. Laboratory tests showed the following results: Open circuit test: V = = 230 V, I =5.7A, P = 190 W Short circuit test: V-41.5 V, I-21.7 A, P-No wattmeter was used. 18 (2) Compute the value of primary voltage needed to give rated secondary voltage when the transformer is connected as a step-up one and is delivering 50 KVA at a power factor of 0.8 lagging. (b) Compute the efficiency under conditions of part (a).
Justify if in a Yy transformer (without neutral wire on the supply side) there are homopolar components in fluxes, voltages and currents, and indicates whether this operation is satisfactory or not
13)This MCQ QUESTION FROM BASIC POWER ELECTRICAL ENGINEERING course.
When the transformer is loaded in a balanced fashion up to its nominal rating (10 MVA), calculate the high side line-to-line phasor voltages (ab, bc, ca). and low side phasor voltages both line-to-line and line-to-neutral (ab, bc, ca, a, b,c). as a reference for calculations the low side A line to neutral voltage is 7620V at an angle of 0 degrees when the transformer is at rated power. The transformer has the following characteristics: V: 138kV delta high side/ 13.2 kV wye low side 9% impedance X/R ratio of 20
a single-phase transformer serves a 7.2kw resistive loadlocated 200 ft from the transformer. each conductor from the transformer to load has an impedence of (0.78+j0.052) ohms per 1000ft. if the voltage at the load terminal is 240v, the magnitude of the voltage (v) at the transformer secondary is most nearly:
A 5750 V/ 260 V, 50HZ single-phase transformer is to have an approximate e.m.f. per turn of 35 V and operate with a maximum value of flux density of 1 T. Calculate (a) the number of primary turns (b) number of secondary turns (c) maximum value of flux and (d) the cross-sectional area of the core. Number of turns in Primary Number of turns in Secondary maximum value of flux Area of cross section
The voltage per winding of the 220V/12V, 50 Hz single phase core transformer is 1V. If the maximum flux density in the core is 1.5 T, which of the following is the cross-sectional area of the core in cm2 ?
A single phase 220/6 Volt, 50 Hz transformer has a rated primary current = 0.5 A. its maximum efficiency is at load current = 15 A and equal to 94% at unity p.f. Its efficiency at rated load, 0.65 p.f. lagging is: 087.8%. 092.3%. 090.9%. ONone.
A single-phase transformer is designed to operate at 2V per turn and turn ratio of 3:1. If the secondary winding is to supply load of 8kVA at 80V. Determine i. the primary supply voltage number of turns on each winding the current in'each winding.