The elements of a floor jack are shown in the figure. The figure CDFE is a parallelogram. Calculate the magnitude of the force in th hydraulic cylinder AB corresponding to the 2270-Ib load supported as shown. What is the magnitude of the force in link EF? Assume W = 2270 lb, a = 2.90 in., b = 3.10 in., c = 4.45 in., d =8.75 in., e = 1.95 in., and f = 1.95 in. W e D a]

The elements of a floor jack are shown in the figure. The figure CDFE is a parallelogram. Calculate the magnitude of the force in th hydraulic cylinder AB corresponding to the 2270-Ib load supported as shown. What is the magnitude of the force in link EF? Assume W = 2270 lb, a = 2.90 in., b = 3.10 in., c = 4.45 in., d =8.75 in., e = 1.95 in., and f = 1.95 in. W e D a]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the forces in all bars of the truss shown in the given figure. Indicate tension or compression. Given: X= 30 kN. BXKN 60 KN The force in member AB (FAB) is The force in member BC (FBC) is The force in member AC (FAC) is[ 6m kN. (Click to select) kN. (Click to select) KN. (Click to select)
Item 2 Consider the following hanging mass system for the following problems. Before answering the questions below, draw two separate free-body diagrams of ring C and then ring B. Be sure the FBDS are neat a properly labeled. You will turn them in with your written work. (Figure 1) Figure 30° E 45° F 1 of 1 Part A cb Deturmine the tension developed in cable if cylindar E weighs 40 lb and 0= 15°. FCB= Submit ▾ Part B WF = 5 ΑΣΦ 11 vec Submit Request Answer If cylinder E weighs 40 lb and 0 = 15°, determine the weight of cylinder F. Express your answer with the appropriate units. 15. ΑΣΦ ↓↑ vec ? Request Answer ? lb 2 of 5
show solutions pls thank you very much :D
Find the forces for bars FE, DF, CE, CF, CD, and BD
The illustrated truss is subject to certain loads. Calculate the forces acting in the components identified as 3-4, 3-10, and 9-10. Attach your solution (Give, Required, Solution with FBD) 0.8 kip 1.6 kips 2 8 ft 8 1.6 kips 3. 1.6 kips 8 ft 4 8 ft 10 1.6 kips 8 ft 5 1/1 1.6 kips 8 ft 6- 12 0.8 kip 6 ft 8 ft 4.5 ft
A schematic of a homemade hydraulic jack is shown in the figure below, with cylindrical tube ends of different radii, r, = 0.0440 m and r, = 0.120 m, respectively. F A (a) If a downward force of F, = 16.0 N is applied to the end with the smaller radius, how much force F, would the jack exert on a car if it were sitting above the other end? (Enter the magnitude.) N (b) If the smaller piston is pushed down a distance d, = 0.208 m, through what distance d, would the other end move?
RAY F Enter Fpc: Enter Fr The figure above is a pin-joint frame with horizontal member length 1 = 2m and vertical member length h = 4m. (Note that the diagram is not to scale.) You are given that F₁ =45kN, RAY = 15kN and Rpy = 30kN. Use the method of sections to calculate the forces in members BC, FC and FE. Enter your answers in kilonewtons (kN) correct to 2 decimal places. Enter Fac: KN KN F₁ KN RDY
Please solve for all and include all steps. Thx
In the fig. shown, compute the ff: (11-13) the tension in cable BD 7.5 rt To = (14-15) the components of the support 10 rt At C. Ch Cv = 5 rt 1000 lb 12.5 ft S00 I In the fig. shown, compute the ff: (16-18) the resultant using cosine law (force polygon) 60 R = 35 (19-20) the angle of the R measured CW from the x- axis. 500 lb
2D truss system below has 5 elements and 4 joints. The truss system is roller supported at joint 1 and pin supported at joint 3. Calculate all member forces of the truss system using the method of joints! Discuss your results! Assume a = 20 ft and P = 8 kips. Perform your calculations on a blank paper using the Given, Find, Analyze layout and draw free-body diagram to describe 2D systems