The electrodialysis of a 0.1 N NaCl solution is carried out in 100 cells. The flow rate of the solution is 1 L/s, the removal efficiency is 60%, and the electrical efficiency is 98%. The current required for operation is most nearly (A) 60 A (В) 200 A (С) 500 А (D) 1000 A

Q: The design fluid (typically water and antifreeze) flow rate through a solar hotwater heater system…

A: The flow rate of the fluid = 0.025 gpmft2or gallonsmin.ft2 Dimension of each solar panel = 4ft×8ft…

Q: A sand pack is used to filter impurities from molten polyester downstream of the extruder and prior…

A: Given data: Temperature of polymer= 280 0C Viscosity of polymer = 650 Pa∙s Density of polymer = 1365…

Q: A rotameter with float shape type "B" (see figure below) has a tube of 0.3 m long. The internal…

A:

Q: Problem 1. ·A filtration process is carried out in the laboratory to filter calcium hydroxide slurry…

A: Given data: -∆P=425000N/m2 Slurry concentration=36kg/m3 Area of filter=0.65ft2 Viscosity at…

Q: A' E Stream A B с D E A' Flow rate (Q, L/s) 120 80 160 Solid (C, mg/L) 2000 20 6000

A: Streamfloe rate (Q, L/s)Solid (C, mg/L)A1202000B8020C6000DEA'160

Q: A concern with plans for capture of CO 2 directly from ambient air (DAC), is the sheer volume of…

A: Given data:speed of fan,height of rectangular installation,thickness of rectangular…

Q: a) Estimate the transition length at the entrance to a 15-mm tube through which 100 percent glycerol…

A:

Q: Problem 1: Reynold's number a rotating brush uses a device similar to the device shown in HD Figure…

A:

Q: A coal-burning electric generating plant emits 1.5 kg/min of SO2 from a stack with an effective…

A: Given wind speed is 5 m/s.From Atmospheric Stability under Various Conditions table (which is given…

Q: Air flows through a pipe, with a mass flow rate of 0.8 kg s-1. A static Pitot be is positioned at a…

A: m*(mass flow rate )= 0.8kg.sec-1Pstat= 4.013barI.D=50×10-3mM.W of air= 29 kg.kmol-1PStag=?

Q: Q3/The supply ductwork for a hotel building is shown below. Determine : - 1. Size of main duct and…

A: A supply ductwork for a hotel buil;ding is given, where,the velocity is given as, ,main duct and…

Q: The following diagram is a simplified polarization curve of Evan's diagram for a carbon steel used…

A:

Q: Design a hydrocooling unit that can cool fruits and vegetables from 30°C to 5°C at a rate of 20,000…

A: Note: We are authorized to answer three subparts at a time, since you have not mentioned which part…

Q: Crude oil at 140°F with y=53.7 lb/ft³ and u= 8x10-5 lb-s/ft2 (about four times the viscosity of…

A: Given that  T = 140 F density = 53.7 lb/ ft3 Viscosity ,u = 8 x 10-5 lbs/ft2 L = 799 mile = 4.22 x…

Hazard Analysis and Design in Chemical Engineering

Hazard is the intrinsic property of a material or process which harms the people, buildings, or environment. Health, safety, hazard, risk assessment, loss prevention, and environmental consideration play an important role while designing a chemical processing plant. Hazard is often confused with risk. Risk measures the magnitude of loss and injury of likelihood incidents or the consequence and frequency of incidents.