The driver attempts to get the car out of the mud by exerting a perpendicular force of 610.0 N, and the distance she pushes in the middle of the rope is 1.00 m while she stands 6.00 m away from the car on the left and 6.00 m away from the tree on the right. What is the tension T in the rope, and how do you find the answer?

Q: Q4/ Determine the magnitude of the mass (m) in the figure shown. Assume there is no friction in Each…

A:

Q: 2. For the frame shown, calculate the reactions at A and B. 240 lb 90 Ib/ft 30 Ib/ft A 20 ft 20 ft…

A:

Q: Find the forces in the three members of the space truss shown in the figure. 600 mm 500 mm 820 mm-…

A:

Q: The free body diagram below shows the forces acting on the bob when it spins at a rate such that it…

A: GivenFS=string force Fe=Elastic force W=weight of the bob

Q: The thin steel plate, weighing 82, is being lifted slowly by the cable AC and BC. Compute the…

A:

Q: Activity 1: The boom AB is supported in the position shown by a cable which runs over a small pulley…

A: Given data:

Q: 150 lb/ft B 6 ft 8 ft

A: divide this load into two parts from A to C and C to B the total load of UVL (from A to C) =…

Q: A small cable car is used to transport passengers across a river. If the cable car and its contents…

A: In the given problem, pulley at B is considered to be frictionless, thus tension on both the sides…

Q: A person pulls on a 500 N desk with a 200 N force acting at 30° angle above the horizontal. The desk…

A: QuestionA person pulls on a 500 N desk with a 200 N force acting at 30° angle above the horizontal.…

Q: Two massless and frictionless pulleys are used to drag a large mass (m = 645 kg) up an inclined…

A:

Q: A construction worker on a job site attempts to move a boulder out of the way by attempting to apply…

A: First, we know a total of "F1 "and "F2 "is equal to "F" and after that, we take a moment about point…

Q: PROBLEM 1: Consider the truss system to the right. All members are two force members. There is a pin…

A: Consider the truss system to the right. All members are two force members. There is a pin at Point D…

Q: in the truss below, the maximum force(s) will occur in members GF, AF, or AB. What component…

A: In the truss below, the maximum force(s) will occur in members GF, AF, or AB.What component sustains…

Q: The resultant of the forces P1, P2, and the couple C is the force R= 35.6k N acting at a point A (R…

A: The given system of force is - Writing the co-ordinates of the point: -

Q: Problem 1 Three masses hang off of the ceiling in the following configuration. Calculate the tension…

A: The value of the mass, The value of the mass, The value of

Q: A machine component is subjected to the forces and couples shown. The component is to be held in…

A:

Q: A fisherman is holding a fishing rod with a large fish hanging from the line. Identify the forces…

A:

Q: Determine the forces at A and B. The force at A is The force at Bis lb 4 lb &

A: This question is based on the concept of classical mechanics on force balancing.

Q: A 50-lb box is suspended by two ropes . Rope A pulls the box horizontally and the other rope is in…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.