The drive drum of a belt conveyor consists of a rope and a pulley. It is stretched by a tensioning mechanism. The rope in the mechanism is where the drive drum is fixed to the center; of a reel located horizontally outside the drum designed in such a way that weight is hung on the end by passing it around. Belt conveyor It is stretched with a force of 4000 kg. Shrinkage in the belt conveyor force is 1900 N and the friction coefficient between the drum and the belt is 0.12. by; What is the angle of wrapping of the belt to the drum?

Q: A hanging weight, with a mass of m, = 0.350 kg, is attached by a rope to a block with mass m, =…

A: Given data as per the question mass m1=0.350 kgmass m2=0.830 kgmass of pulleyM=0.350 KGRadius…

Q: A disk with radius r = 0.3 m, mass = 50 kg is tethered to the wall and subjected to a downward…

A: Givenr=0.3mm=50kgμ=0.15

Q: The weight of the trunk (Wtrunk) is 500 N, and it has a moment arm of 0.10 m. The weight of the arms…

A: The objective of the question is to calculate the back extensor force (F_m), bone compressive force…

Q: As shown in the figure below, a uniform beam is supported by a cable at one end and the force of…

A: Given Data:Angle Length Coefficient of static friction      Weight of the shaft = To Determine:The…

Q: Two mass m,= 6 kg connect to mass m2=4 kg and both masses with block of mass m;=2.5 kg are attached…

A:

Q: Please write the problem on paper, I do not like it when it is typed out on the computer. Need help…

A: Approach to solving the question: Detailed explanation: Examples: Key references:

Q: A 110-kg uniform ladder is tied at its bottom on the wall using a wire shown in the figure. The…

A: Given, The mass of the ladder, m = 110 kg The maximum tension in the wire, T = 180 N

Q: The roof over a 9.0-m x 10.0-m room in a school has a total mass of 12900 kg. The roof is to be…

A:

Q: Problem 2: Mass A is suspended from a cable that wraps around a frictionless and massless pulley at…

A:

Q: Problem 2: A flat plate, shown below, with a fillet radius of 0.1875 in. is subjected to an axial…

A:

Q: The drawing shows a uniform horizontal beam attached to a vertical wall by a frictionless hinge and…

A:

Q: *Prob. 1.4-6. A portion of the boom of a crane at a construc- tion site is shown in Fig. P1.4-6. The…

A:

Q: A cylinder is moving a 6000 lb load up a 20° slope as shown in the figure below. The friction…

A: Given: Angle of inclination→θ=20° Friction coefficient between the surfaces→μ=0.4 Mass of the…

Q: A steel panel is subjected to a compressive loading in order to improve the panel stiffness and to…

A: Given:- F=400kips V= 0.20 E=2.8x107psi

Q: The figure shows a system composed of a disk of weight W1 = 901b and radiius r = 6.7 in connected to…

A: Given information: The weight of the disk (W1) = 90 lb The radius of the disk (r1) = 6.7 in The…

Q: A truck bed cargo shell has a rectangular glass window that is held up by two strut pistons. Assume…

A:

Q: I just need to see a diagram of what problem 3 would look like.

A: Given:The width of the door is w.Angle between the hinges and the vertical axis is .

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.