The double-offset joint is typically used in applicationsthat require __ .a. higher operating angles and greater plunge depthb. lower operating angles and lower plunge depthc. higher operating angles and lower plunge depthd. lower operating angles and greater plunge depth

Q: A fillet weld can be used to join which of the following joint types: *

A:

Q: discussion of the temperature distribution problem along rod

A: We will use the fin analogy , a cylindrical is heated at the base and cooled by convection , had…

Q: It asks what is the width across the flats of the locking bolt head?

A: The width across the flats of the locking bolt head is 0.5625

Q: Cantilever Method assumes that the mid-height of the column is a location for point of inflection.…

A: Correct answer: True

Q: I need the answer for problem number 14.

A: 14.In this drawing, only one chamfer is represented by the leader line. The chamfer is represented…

Q: A fillet weld can be used to join which of the following joint types: * O All of the Mentioned O Tee…

A: Correct answer: All of the mentioned

Q: the rim and face alighnment method is a.used only to alighn solid flange couplings b.less accurate…

A: Rim and face method is also called the dial indicator method. it consists of the installment of two…

Q: 6.25 ft 12.5 ft , 12.5 ft , 12.5 ft , 12.5 ft Ans. B D F H FCE = 8,000 lb, T 15 ft FDE = 2,600 lb, T…

A:

Q: Draw the welding symbol from the following information. SINGLE J BUTT WELD CONVEX FACE SIZE 5 mm…

A: Given: Drawn the welding symbols.

Q: In determining the net cross sectional area of a structural steel tension member, the diameter of a…

A:

Q: If 4 lengths of support brace are required for a job, 34 13" and 45 57 1", what is the total length…

A: Given Data⇒ Lengths of subparts is : L1=341316''L2=4578''L3=291516''L4=5714''

Q: Calculate the heat input during the arc welding process, if the voltage is 28 volts, current is 114…

A:

Q: Truss members can change their length due to a change in temperature. True or false?

A: In truss members, there is no change in length. But due to changes in temperature stress is build up…

Q: 20. What is the minimum diameter for a plug weld deposited in a hole drilled in a plate '/2 in.…

A: Plug welds are circular welds that connect two surfaces by passing through a tiny hole in one of…

Q: Which of these welds could be analyzed using the AISC Code's "kips per inch" method? (Indicate all…

A: AISC stands for American institute of steel construction.It is basically quality management system…

Q: Draw the Welding symbol based on the data given • SINGLE BEVEL BUTT WELD • Flat FACE • SIZE 45 mm •…

A: Given data  SINGLE BEVEL BUTT WELD Flat FACE SIZE 45 mm HIDDEN SIDE ALL AROUND WELD To Draw the…

Q: Why are all welds not inspected to the same level orstandard?

A: Information Provided: Not all welds undergo the same level or standard of inspection. Not all welds…

Q: 7 6 5, 4 3 2. 1 The part pointed by number 4 is 10 11 12 13 14 16 17 18 19 -20 21 22 oil galleries.…

A:

Q: Find the eccentricity of the welded connection by using 5 mm fillet weld. -120 mm - 200 mm 400 mm X-…

A:

Q: Universal joint is used for non parallel shafts whose axes are O coplanar. connecting radiator…

A: Universal joint: The universal joint is a joint between two rotating shafts which allows to move the…

Q: Sketch the groove welds specified and show all given weld dimensions

A: Sketch the groove welds The groove weld is a most common welding in which root opening is present.…

Q: In arc welding, if the electrode cable is negative, it is called --------------- polarity and…

A: This question is from welding technology.

Q: Note: the drawing below shows the end view of a weldment consisting of 7 tubes. 8.625" 4. What is…

A: It is required to determine c to c distance

Q: How many inches of weld are required around each end of the BI pipe? (use

A: Given:  In the drawing there are 2 Bi pipes

Q: What happens if the load on an actual column exceeds its critical loading?

A: There are two types of the column, 1. Short Column 2. Long Column The slenderness ratio and length…

Q: Which type of joint has a flatter design than anyother?a. Double-offsetb. Discc. Cross grooved.…

A: The cross groove joint uses balls and V-shaped grooves mostly on inner and outer races to cater the…

Q: DOUBLE FILLET WELD CONCAVE FACE SIZE 20 MM

A: Double Fillet Weld A double fillet weld occurs when a fillet weld is required on both sides of the…

Q: How many categories of weld are associated with Weld symbols

A: There are so many categories of welds, these are given as with symbols, (1) Butt weld between plates…

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: The term, Orthogonal, describes the relationship of the axis of the ½” NPT pipe plug with the main…

Q: write three disadvantages of tee pipe

A: Tee pipes

Q: The largest soft aluminum tubing that may bent by hand is ________________ -inch outside diameter. *

A: Solution:

Q: Explain minimum 3 types of welding position for groove and fillet weld?

A: WELDING  Welding is a manufacturing method through which two or more components are joined by heat,…

Q: a fillet w eld is 5 r jual to: )14.14 r

A: given:length of weld l=5mm

Q: 11)lf length of a fillet weld is I and leg length is h, then area of throat can be given by:

A: The length of the fillet weld is l. The leg length is h.

Q: In most cases, pre-loading a bolted tensile joint increases the fatigue factor of safety. has no…

A:

Q: The short columns fail due to ________ Select one: a. Crushing

A: There are three types of columns, Long columns, intermediate columns and short columns.

Q: What weld section properties are required to analyze the weld between the horizontal tube and the…

A:

Q: Joining the sheets at specific locations under the heat and pressure is known as Select one: a.…

A:

Q: Application areas of some welding methods are given below. Match the welding method with the given…

A: A. Root pass welding of reactive materials B. Thin-Walled pipe welding C. In the production of…

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.