The distance between points is exactly 100 ft. This measurement is read correctly on steel surveyors tape at 70°F and with a 10-lb tension. If the tape measures another distance as 100ft at 100°F and with 20-lb tension, what is the actual distance? The tape is 3/8-inch wide and 1/32-inch thick. A. 100.0443ft B. 100.0332ft C. 100.0223ft D. 100.0112ft

Q: An engineer’s level with stadia constant of 0.3 and stadia interval factor of 100 was set up at on…

A: Given Datak=100c=0.3d=ks+cD=100(1.33+1.02)+0.3D1=235.3 D2=100(1.972+1.736)+0.3D2=371.1 m

Q: A line measured with a 50-m steel tape was recorded as 352.70 m. If the tape is 50.08 m long during…

A:

Q: traverse are as follows: AB= 202.74, BC=285.87, CD=499.37, DE=321.33, and EA = 382.78. (Note: Assume…

A:

Q: A 1-2 line was divided into sections on sloping terrain using a 30-meter tape, and the subsequent…

A:

Q: 1)Given the following set of stadia level notes. The instrument used has a stadia and C =…

A: Given Stadia interval, k = 100 C = 0.229 Table with back sight and foresight details, Stadia…

Q: The following bearings taken on a closed compass. Compute the bearing of line AF. Forward Bearing N…

A: Given data LINE FORWARD BEARING BACKWARD BEARING AB N 38°10' E S 38°20' W BC N 54°13' E S…

Q: Example : The following bearing of the lines observed for closed tränverse ABCDA with the surveyor…

A:

Q: Compute and illustrate the cross-sectional area. (Use trapezoidal rule) 2. Given the chainage data…

A:

Q: In 1860 the magnetic bearing of a line was N 69 deg 27 min W with a magnetic declination of 5 deg 12…

A:

Q: I would like an example of how to calculate the bearing and the distances. I can't seem to figure…

A: Information required: Northing represents latitude and Easting represents departure. Given:  For…

Q: UPVOTE WILL BE GIVEN! Write the solutions legibly. Answer in 2 decimal places. FUNDAMENTALS OF…

A:

Q: Given the three-wire leveling note below, find the elevation of BM2 and perform the customary…

A: Given: The data for the three-wire levelling is given as: To Determine: The elevation of BM2 and…

Q: Q2: Given the following planar manipulator find the following a) °T2 b) 2R, c) The location of 02…

A: Planar manipulator: A manipulator is called a planar manipulator if all the moving links move in…

Q: OBSERVED BEARINGS COMPUTED ADJUSTED ANGLES LINE LENGTH (m) STA INTERNAL Corr INTERIOR FORWARD ВАCK…

A: Interior included angle of the traverse = Fore bearing of the preceding line - Back bearing of…

Q: State the stability criteria of cantilever retaining wall ?

A: Cantilever retaining wall Cantilever retaining walls are constructed of reinforced concrete. They…

Q: Convert and perform the following and show the answer in bearings: S87°19’33’’W + 19°12’59’’

A:

Q: A line measured with a 50-m steel tape was recorded as 352.70 m. If the tape is 50.08 m long during…

A:

Q: On a vertical photograph of flat terrain, section corners, which are a nominal 1-mi apart, appear a…

A:

Q: LINE AZIMUTH FROM NORTH AB ВС CD DE EF

A:

Q: Given are the interior angles of a heptagon. Determine the discrepancy for the givenobservation and…

A:

Q: Direct measurements of volume is rarely made in surveying. O a. Only true if computing earthworks O…

A:

Q: A 55°25' D S 80°21'E N 85°31'W B a. North 29 degrees 05 minutes West b. South 30 degrees 06 minutes…

A:

Q: Adjusted Values Corr Interior Angle Observed Bearings Length (m) Computed Sta Internal Angle Line…

A:

Q: A field is in the form of a regular pentagon. The direction of the bounding sides was surveyed with…

A:

Q: 10. Complete the following table using the knowledge obtained in class about differential leveling…

A: Complete the following table using the knowledge obtained in class about differential leveling

Q: A 100 m tape weighing 3 kg was standardized and found to be 0.02 m short at temperature of 10degC…

A:

Q: 2. An engineer's level with stadia constant of 0.3 and stadia interval factor of 100 was set up at…

A: stadia constant =c =0.3 stadia interval factor= 100

Q: 1)Given the following set of stadia level notes.The instrument used has a stadia interval factor of…

A: GIVEN Stadia interval factor, k = 100 C = 0.229 Stadia interval, s Angle, θ Rod reading, RR TO…

Q: Computed Lat Computed Dep Correction Adjusted Lat Adjusted Dep Course Length, m AZn Bearing +N -s +E…

A:

Q: 4. The exterior angles of a traverse were measured using a theodolite and the readings are given…

A:

Q: Choose the letter of the answer. A line was measured and found out to be 512.21 m. it is then found…

A:

Q: A 50-m tape was used to measure distance AB as 945.60m. The tape was discovered to be 50.075m after…

A: Given data, Designated tape length l = 50 m Actual tape length la = 50.075 m Length to be measured L…

Q: 3. What must be the actual measurement to a (GML) meters distance using L(10) meter tape that is…

A:

Q: In 1860 the magnetic bearing of a line was N 69 deg 27 min W with a magnetic declination of 5 deg 12…

A: Given data in question  Manetic bearing in 1980 = N 69°27` Declination in 1980 and present = 5°12`…

Q: Please enlighten me on how did they get those values that I encircled. Thank you very much! I'll…

A: The encircled value of 91.8 kN has come from the concentrated load 34 kN at point B.

Q: In 1860 the magnetic bearing of a line was N 69 deg 27 min W with a magnetic declination of 5 deg 12…

A: To determine the magnetic bearing of the line today.

Q: May I ask if the answer for this problem is q =11.44? It think the answer key is wrong of otherwise,…

A: You are correct as per the diagram and calculations shown

Q: Question 1 Listen For 0° < 0 < 360° ,find the angles that satisfy the equation cos(0) = 0.2857 Round…

A: ● solution:- b)  As we can see that the values are given like:- cos @ = 0.2857  And @ value should…

Q: What is the whole circle bearing of line OC? D 30 60° 55° C 45° O a. S 55 deg W O b. 55 deg O c. 235…

A: In the whole circle bearing, the magnetic North line is considered as the reference line. In the…

Q: The following offsets are taken from a chain line to an irregular boundary towards right side of the…

A:

Professional survey

A professional survey is a systematic questionnaire that the target audience fills out online, usually by filling out google forms. Professional surveys can vary in length and format. The data is stored on a website and the testing tool usually provides a certain level of data analysis in addition to a professional expert review. Several professional online survey softwares are present worldwide like, SoGoSurvey, SurveyGizmo, SurveyMonkey, Qualtrics, and so on.