Homework Help is Here – Start Your Trial Now!
Engineering
Mechanical Engineering
The Diamond Ring Solution. The processing chip on the computer that controls the navigation equipment on your overheating. Unless you fix the problem, the chip will be damaged and the navigation system will shut down. You open the panel and find that the small copper disk that was supposed to bridge the gap between the smooth top of the chip and the cooling plate is missing, leaving a 2.0 mm gap between them. In this configuration, the heat cannot escape the chip at the required rate. You notice by the thin smudge of thermal grease (a highly thermally conductive material used to promote good thermal contact between surfaces) that the missing copper disk was 2.0 mm thick and had a diameter of 1.0 cm. You know that the chip is designed to run below 70 °C, and the copper cooling plate is held at a constant 5.0 °C. (a) What was the rate of heat flow from the chip to the copper plate when the original copper disk was in place and the chip was at its maximum operating temperature? (b) The only material that you have available on board to bridge the gap between the chip and copper plate is lead. If the cross- sectional area of the lead piece you plan to wedge into the gap is 1.0 cm², what is the rate of heat flow from the chip to the copper plate? Does it match the value calculated in part (a)? (c) While brainstorming for other possible solutions to your problem, you happen to glance down at the engagement ring on your finger: a large, glittering diamond. The top and bottom surfaces are flat and nearly rectangular (L= 0.75 cm and W-0.50 cm), and the thickness looks to be about 2.0 mm, just right to bridge the gap. You pry the diamond out of its holder and press it into the gap. What is the rate of heat flow now? Good enough?

The Diamond Ring Solution. The processing chip on the computer that controls the navigation equipment on your overheating. Unless you fix the problem, the chip will be damaged and the navigation system will shut down. You open the panel and find that the small copper disk that was supposed to bridge the gap between the smooth top of the chip and the cooling plate is missing, leaving a 2.0 mm gap between them. In this configuration, the heat cannot escape the chip at the required rate. You notice by the thin smudge of thermal grease (a highly thermally conductive material used to promote good thermal contact between surfaces) that the missing copper disk was 2.0 mm thick and had a diameter of 1.0 cm. You know that the chip is designed to run below 70 °C, and the copper cooling plate is held at a constant 5.0 °C. (a) What was the rate of heat flow from the chip to the copper plate when the original copper disk was in place and the chip was at its maximum operating temperature? (b) The only material that you have available on board to bridge the gap between the chip and copper plate is lead. If the cross- sectional area of the lead piece you plan to wedge into the gap is 1.0 cm², what is the rate of heat flow from the chip to the copper plate? Does it match the value calculated in part (a)? (c) While brainstorming for other possible solutions to your problem, you happen to glance down at the engagement ring on your finger: a large, glittering diamond. The top and bottom surfaces are flat and nearly rectangular (L= 0.75 cm and W-0.50 cm), and the thickness looks to be about 2.0 mm, just right to bridge the gap. You pry the diamond out of its holder and press it into the gap. What is the rate of heat flow now? Good enough?

Elements Of Electromagnetics
Elements Of Electromagnetics
7th Edition
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Sadiku, Matthew N. O.
ChapterMA: Math Assessment
Section: Chapter Questions
Problem 1.1MA
See similar textbooks
icon
Related questions
Question
The Diamond Ring Solution. The processing chip on the computer that controls the navigation equipment on your spacecraft is overheating. Unless you fix the problem, the chip will be damaged and the navigation system will shut down. You open the panel and find that the small copper disk that was supposed to bridge the gap between the smooth top of the chip and the cooling plate is missing, leaving a 2.0 mm gap between them. In this configuration, the heat cannot escape the chip at the required rate. You notice by the thin smudge of thermal grease (a highly thermally conductive material used to promote good thermal contact between surfaces) that the missing copper disk was 2.0 mm thick and had a diameter of 1.0 cm. You know that the chip is designed to run below 70 °C, and the copper cooling plate is held at a constant 5.0 °C. (a) What was the rate of heat flow from the chip to the copper plate when the original copper disk was in place and the chip was at its maximum operating temperature? (b) The only material that you have available on board to bridge the gap between the chip and copper plate is lead. If the cross- sectional area of the lead piece you plan to wedge into the gap is 1.0 cm2, what is the rate of heat flow from the chip to the copper plate? Does it match the value calculated in part (a)? lem, (c) While brainstorming for other possible solutions to your happen to glance down at the engagement ring on your finger: a large, glittering diamond. The top and bottom surfaces are flat and nearly rectangular (L = 0.75 cm and W=0.50 cm), and the thickness looks to be about 2.0 mm, just right to bridge the gap. You pry the diamond out of its holder and press it into the gap. What is the rate of heat flow now? Good enough?
Transcribed Image Text:The Diamond Ring Solution. The processing chip on the computer that controls the navigation equipment on your spacecraft is overheating. Unless you fix the problem, the chip will be damaged and the navigation system will shut down. You open the panel and find that the small copper disk that was supposed to bridge the gap between the smooth top of the chip and the cooling plate is missing, leaving a 2.0 mm gap between them. In this configuration, the heat cannot escape the chip at the required rate. You notice by the thin smudge of thermal grease (a highly thermally conductive material used to promote good thermal contact between surfaces) that the missing copper disk was 2.0 mm thick and had a diameter of 1.0 cm. You know that the chip is designed to run below 70 °C, and the copper cooling plate is held at a constant 5.0 °C. (a) What was the rate of heat flow from the chip to the copper plate when the original copper disk was in place and the chip was at its maximum operating temperature? (b) The only material that you have available on board to bridge the gap between the chip and copper plate is lead. If the cross- sectional area of the lead piece you plan to wedge into the gap is 1.0 cm2, what is the rate of heat flow from the chip to the copper plate? Does it match the value calculated in part (a)? lem, (c) While brainstorming for other possible solutions to your happen to glance down at the engagement ring on your finger: a large, glittering diamond. The top and bottom surfaces are flat and nearly rectangular (L = 0.75 cm and W=0.50 cm), and the thickness looks to be about 2.0 mm, just right to bridge the gap. You pry the diamond out of its holder and press it into the gap. What is the rate of heat flow now? Good enough?
Expert Solution
trending now

Trending now

This is a popular solution!

steps

Step by step

Solved in 6 steps with 12 images

SEE SOLUTIONCheck out a sample Q&A here
Blurred answer
Follow-up Questions
Read through expert solutions to related follow-up questions below.
Follow-up Question

C is not correct

Solution
Bartleby Expert
SEE SOLUTION
Knowledge Booster
Convection
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Recommended textbooks for you
Elements Of Electromagnetics
Elements Of Electromagnetics
Mechanical Engineering
ISBN:
9780190698614
Author:
Sadiku, Matthew N. O.
Publisher:
Oxford University Press
Mechanics of Materials (10th Edition)
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:
9780134319650
Author:
Russell C. Hibbeler
Publisher:
PEARSON
Thermodynamics: An Engineering Approach
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:
9781259822674
Author:
Yunus A. Cengel Dr., Michael A. Boles
Publisher:
McGraw-Hill Education
Control Systems Engineering
Control Systems Engineering
Mechanical Engineering
ISBN:
9781118170519
Author:
Norman S. Nise
Publisher:
WILEY
Mechanics of Materials (MindTap Course List)
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:
9781337093347
Author:
Barry J. Goodno, James M. Gere
Publisher:
Cengage Learning
Engineering Mechanics: Statics
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:
9781118807330
Author:
James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:
WILEY
SEE MORE TEXTBOOKS