The diameter of the pin b and the cable connected in c, which is in a single slide with 6 mm diameter, is 3 mm. The operating normal and shear stresses of the accelerator pedal system are 140 MPa and 28 MPa, respectively. Determine the maximum force P that can be applied to the foot pedal?

Q: In a procedure to evaluate the strength of the tri- ceps muscle, a person pushes down on a load cell…

A:

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: 3. Link AB shown in Fig. Q3 is supported by cable AC which is made of aluminium with Modulus of…

A:

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A:

Q: The frame shown is fitted with three 28 cm diameter frictionless pulleys. A force of F' = 640 N is…

A:

Q: below shows a stee! bar 07 mass m The 7igure which is placed against a wall. There is no betneen the…

A:

Q: A steel rod is 0.02-m in diameter and 2.5-m in length. The modulus of elasticity ofthis material is…

A: Diameter of steel rod d=0.02m, Length of steel rodL=2.5m. Tensile Force P=150KN=150×103N, Modulus of…

Q: find the required wall thickness of the cylinder.

A: find the required wall thickness of the cylinder.

Q: A mechanism is used to apply a constant load Q to the seat in the manner illustrated. 1. Determine…

A: Length OC=1000mmQ=700N To-Find:- 1. The lengths of LBE and LAB, in m   Degrees, the angles 2.…

Q: A punch press has sufficient capacity to punch six holes 26 mm in diameter in a 20-mm boiler plate.…

A: Given, Number of holes to be punched = n = 6 Diameter of holes = D = 26 mm Thickness of holes = t =…

Q: A 40 mm diameter rod of a certain material is 1,2 m long and has a collar fitted to one end. The rod…

A: Diameter is 40 mmLength is 1.2 mWeight Extension Maximum stress in bar

Q: Q2/ Determine the forces at the pin joint (F) and the roller support (G) ? 30KN 20 KN 2m BY 2m D 2m…

A:

Q: The elastic limit of a steel elevator cable is 275 MPa. What is the maximum up acceleration than can…

A: givenelastic limit of cable σ=275MPamass of elevator m=900kgcross section A=3cm2=300mm2stress not…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: A pair of pliers grips the bolt as shown below. 30 mm X₁ B 70 mm X₂ Note: tan 0=y₁/x₂ (a) For the…

A: (a) Draw the free-body diagram of each parts of the pair of pliers.

Q: An L-shaped bracket is supported by a frictionless pin at A and a cable between points B and D. If…

A:

Q: Find the maximum stress in the belt.

A: Given data; T1-T2= 100 Nb= 1cm =0.01 mt =0.5 cm=0.005 mθ= 1700=170×π180=2.967 radv= 1000…

Q: Problem 2.2 Consider the following load raising system. a) Calculate the power of the motor if the…

A: Given figure  To calculate  (a)Calculate the power of the motor if the load is to be raised at a…

Q: Compute for (a) the force exerted on the bolt and rivets at joints A, B, and C and (b) the normal…

A:

Q: Determine the magnitude of the pin force at A. Assume W - 875 lb, a 2.9 ft, b-2.4ft, r - 6 in. "" W…

A:

Q: MAKE A FREE BODY DIAGRAM A horizontal bar 10m long and of negligible weight rests on rough inclined…

A: Given Data The length of the bar is: L=10 m The angle of friction is: ϕ=15° The load acting at the…

Q: Q2/ Determine the forces at the pin joint ? (F) and the roller support (G) 30KN 20 KN 2m BY 2m D 2m…

A:

Q: compression force of 50 N applied on the round bar of 500 mm diameter,  Calculate the stress…

A: Given:compressive force, F=50 Ndiameter of the round bar, d=500 mm or 0.5 m

Q: Q2 / A belt drive consist of two V- belts in parallel, on grooved pulleys of the size. The angle of…

A: Given data: - The density of belt material is ρ = 1.2 Mg/m3. The groove angle is θ = 30 o.

Q: A coil spring with 5 cm outside diameter is required to work under the load of 190 N. The wire…

A: Outside Diameter (D) = 5 cm = 50 mmWire Diameter (d) = 5 mm Active Coils = 6

Q: Find the value of strain if initial length of rod is 100 m and change in length of rod due tensile…

A: Given data : Initial length of rod=L Change in length of rod=∆L   Required : Strain

Q: 2. The three lat blocks are position as Shown in figure below and the force "P parallel to the…

A:

Q: Please solve the problem with a neat paper sheet. The length AB for the lug wrench shown below is 12…

A:

Q: Two pulleys rotating in opposite direction has the following properties: D1 = 430 mm, D2 = 180 mm,…

A: The given information in the problem is listed in the following attached image:

Q: The compound steel bar shown in Fig. Q1(b) made of three uniform segments marked as 1, 2 and 3 of…

A:

Q: 40 &N Fig.4

A:

Q: A steel cable with a diameter of 3.0cm supports a load of 2.0 kN. What is the frictional length…

A:

Q: O Torsion Аxial O Bending Transverse Shea O O

A: At point B the most impact on design will be of torsional shear stress, caused by the torsion.

Q: At a point in a bar of cast iron, the principal stresses are 60 MPa tensile and 120 MPa compressive…

A: Given:Principal stresses:σ1=60 MPa      Tensileσ2=120 MPa     Compressiveσ3=0Elastic limit in…

Q: 2. Link BD is made of brass (E = 103 GPa ) and has a cross-sectional area of 258 mm?. Link CE is…

A:

Q: A steel panel is subjected to a compressive loading in order to improve the panel stiffness and to…

A: Given:- F=400kips V= 0.20 E=2.8x107psi

Q: I need the answer as soon as possible

A: Given data;   T1-T2=100 N    b=1 cm=0.01 mt=0.5cm=0.005 mθ=1700=170 × π180= 2.967 radv=1000m/min…

Q: given loading is

A:

Q: Determine the magnitude of the vertical force A, for the simply supported beam, where w = 9 kips/ft,…

A: