The ??? diagram for a collagen fiber bundle fromwhich a human tendon is composed is shown.σ (ksi)4.503.753.002.251.500.750.050.10125 lb€ (in./in.)If a segment of the Achilles tendon at A has a lengthof 6.5 in. and an approximate cross-sectional area of0.229 in2, determine its elongation if the footsupports a load of 125 lb, which causes a tension inthe tendon of 343.75 lb.(Figure 1)

Given : L = 6.5 inches A = 0.229 in2 To find : Determine the elongation ?

Answered: The ??? diagram for a collagen fiber…

Engineering

Civil Engineering

The ??? diagram for a collagen fiber bundle from which a human tendon is composed is shown.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Fyodor the bald is standing on the diving board of a certain swimming pool. Because of his weight,…

Q: Example Two parallel plates are separated by a thin gap of thickness h containing a Bingham plastic.…

Q: The rectangular plate ABCD undergoes deformation as shown with the dashed lines. Find the average…

A: The rectangular plate ABCD undergoes deformation as shown with the dashed lines. Find the average…

Q: During laboratory testing of an 8-inch steel-alloy rod with a cross sectional area of 32in a tensile…

A: To find modulus of elasticity and Poisson's ratio

Q: A two pinned end bars AB (Copper), A=850 mm², E = 120 GPa and BC (Aluminum), A= 1000mm², E = 70 GPa…

A: Given: The area of bar AB is 850 mm2. The modulus of elasticity of copper is 120 GPa. The area of…

Q: From studying Steel Design, we became familiar with the different philosophies that are used in…

A: Brief concept introduction- Steel design is a branch of structural engineering that deals with the…

Q: The beam shown in figure carries a concentrated load of w and total u.d.l load of 8 w , determine…

A: Procedure to find the maximum safe value of load: The steps in order to find the maximum safe load…

Q: e the change in length (in inches) of the b 000 ksifor bronze, and 10080 ksi for alum Steel 2 ft…

Q: How many Phases and Constituents are in the following material? А В 50 pm

A: Answer - One phase and 2 constituents Any section of a substance with a distinct crystal structure…

Q: The truss shown supports an automobile which has a mass of 2000 kg. Each member of the truss has…

Q: The components of all forces acting on member ABCD are: D= lb ↑ Bx= By= C= Ax= Ay= lb + lb ↓ lb ↓ lb…

Q: Explain the loading details of the structure member below (illustrate with diagrams and types) Load…

A: Multiple elements are used to transmit and resist external loads within a building. These elements…

Q: Determine the yield modulus of elasticity and yield strength of an aluminum material with the…

A: The stress is taken in y-axis and strain in x-axis. From the data, stress-strain curve are being…

Q: For the box beam shown in Fig. if the modulus of elasticity E = 200 GPa, the flexural stresses at…

Q: Ⓡ the total shear force V acting on the cross section is 1,750 N and each nail may carry 860 N in…

Q: An alloy steel having a diameter of 0.45 in. extends 0.002 in. over a gage length of 2.2 in. due to…

Q: Define elastic and plastic behaviors at the micro and macro levels.

A: The objects which are smaller are termed as microlevel objects. The objects which are larger are…

Q: Figure shows a beam made from bronze subjected to a 3.5 kN.m bending couple and its respective…

A: Given- Bending Moment M=3.5 kn-mYoung's modulus of Bronze=96Gpa

Q: (a) determine the average shear stress and shear strain in each of rubber blocks (b) determine the…

Q: How much deformation does a mass of 1 kg falling from a height of 6 meters cause to the built-in…

Q: For the composite body shown in Figure 3, determine the location of the centroid (7,9) relative to…

Q: Discuss how the steel structure will contribute to sustainable development. Include the discussion…

A: Steel has a high recycling capability, which results in less waste, energy consumption, and…

Q: A piece of Titanium originally at 300 mm long is pulled in tension with a stress load of 40,000…

A: Given data - Length of titanium piece = 300 mm Stress = 40000 psi Find out - What is the elongation…

Q: For the given figure below, determine the force that would cause the bar to deform by 1.8x10^-2…

Q: During laboratory testing of an 6-inch aluminum-alloy rod with a cross sectional area of 0.32in², a…

A: Given data : Initial Length (Li)=6 inInitial area (AI)=0.32 in2Tensile load (P)=50000 lbsFinal area…

Q: At room temperature (20°C) a 0.5-mm gap exists between the ends of the rods shown. At what temp will…

A: The change in temperature with respect to the initial temperature of the material tends to change in…

Q: Explain the relationship between the toughness, stress and strain of a material.

A: Hi! Thank you for the question. As per the honor code, we’ll answer the first question since the…

Q: The cross-sectional area of the bar is 5 cm. Use E = 70 GPa for aluminam, and E= 200 GPa for steel.…

Q: Actual weight of steel bars = 1.520 kg/m, Standard weight of steel bars (16mm )= 1.579 kg/m, Load at…

Q: 4. A steel wire 2 m long and 3 mm in diameter is extended by 0.75 mm when a weight W is suspended…

A: Given data: Length of steel wire, ls = 2 m = 2000 mm Diameter of steel wire, ds = 3 mm Elongation in…

Q: A high-strength bolt that is passing through a steel plate is subjected to a tension force of P=4.6…

A: Given Data: Diameter of the bolt is db=12 mm. Diameter of the hole is D=14 mm. The tensile force on…

Q: Condition #1: A structural support for a machine is subjected to a static compression load of 20 kN.…

A: The steps of solving this problem are We have to calculate the compressive load on steel we have…

Q: Cables in a suspension bridge are subject to twisting, that causes shear stresses. Vith this…

A: Answer - B Fiber slide over each other

Q: Which of the following options are correct for the section shown in figure? 40 mm 100 mm 100 mm…

A: Given data, To find the (a)elastic section modulus (b)Shape factor

Q: strength of materials If the steel rod shown is acted upon as shown below, compute for the total…

A: Given data : Area (A)=25 mm2Length of KL (LKL)=500 mmLength of LM (LLM)=800 mmLength of MN (LMN)=400…

Q: Discuss the concept of elasticity and plasticity in materials?

A: The ability of a material to respond to external loads through elasticity and plasticity is one of…

Q: In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards.…

A: Given, Tensile working stresses for the plywood =1245psi Tensile working stresses for the boards…

Question

The ??? diagram for a collagen fiber bundle from
which a human tendon is composed is shown.
σ (ksi)
4.50
3.75
3.00
2.25
1.50
0.75
0.05
0.10
125 lb
€ (in./in.)
If a segment of the Achilles tendon at A has a length
of 6.5 in. and an approximate cross-sectional area of
0.229 in2, determine its elongation if the foot
supports a load of 125 lb, which causes a tension in
the tendon of 343.75 lb.
(Figure 1)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For items 4 and 5. A circular cylinder is welded on the center of the base of a rectangular prism, forming a hammer-like object. The mass of the cylinder is 2kg, and the mass of the rectangular prism is 10kg. The origin of the rectangular axes is at the centroid of the cylinder. 0.0823 kg-m^2 0.1789 kg-m^2 0.982 kg-m^2 1.082 kg-m^2 10cm 0.329 m 0.313 m 30cm 0.1221 m 0.0907 m 30cm yiz diam. d=7cm 4. Which of the following is closest to the moment of inertia of the composite object about the z-axis? Z 10cm 5. Which of the following is closest to the radius of gyration of the composite object about the z-axis?
I need the answer as soon as possible
For the given figure below, determine the force that would cause the bar to deform by 1.8x10^-2 inches. Other properties: X-sectional area: 0.25 in^2. E-steel 29x10^6 Ibs/in^2 E-alum= 10x10^6 lbs/in^2. P- Steel Steel Aluminan C 2440 Ibs 04550 Ibs 03520 Ibs 4450 Ibs
Which materials tend to exhibit elastic perfectly plastic behavior?
STRENGTH OF MATERIALS\ What will be the elongation of a steel bar 40mm x 40mm square section when it is subjected to an axial tensile load of 200kN, Length is 2m and modulus of elasticity E=200GPa.
1. It is a structure used by structural engineers to perform simple force analysis and is effective in estimating the responses such as reactions, shears, moments and etc. a)Structural sketch b)Idealized Structure c)Influence Lines d)Load path
Actual weight of steel bars = 2.340 kg/m, Standard weight of steel bars (20mm )= 2.470 kg/m, Load at yield point = 13100 kgf ,Load at breaking point = 14500 kgf, Maximum load = 18200 kgf, Unit weight of steel = 0.2834 lb/in^3. What is the cross-sectional area in ft^2, Yield strength, ultimate strength and breaking strength in psf?
A beam of a T cross section is formed by nailing together two boards having the dimensions shown in the figure. 240 mm 60 mm 200 mm 60 mm If the total shear force V acting on the cross section is 1,300 N and each nail may carry 400 N in shear, what is the maximum allowable nail spacing s (in mm)? (Assume that the shear force acts parallel to the y-axis and is uniformly distributed across the thickness of the web.) mm
• Calculate all two force members of the plane • Vertical Support at A and D -Include direction (upward, downward, N, E, W, S, or if Tensile or Compressive -Include 4 decimal points -Provide a readable solution -
Find the required properties for the following sections The area of W33X130 in mm? • The moment of inertia about the x-axis for W10X112 in mm“ The radius of gyration of L50X50X3 along the x-axis in mm The distance from the outer face of the web to the centroid of C6X13 in mm The elastic section modulus of C9X20 about the y-axis in mm3
The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The cross-sectional area of the steel, bronze, and aluminum are 0.75 in2, 1.08 in2, and 0.56 in2 respectively.Determine the change in length (in inches) of the bar if P = 11599 lb.The moduli of elasticity are 30022 ksi for steel ,12071 ksifor bronze, and 10028 ksi for aluminum. Round off the final answer to four decimal places.