The d-14-mm-diameter solid rod passes through a D-19-mm-diameter hole in the support plate. When a load Pis applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b= 11 mm. The rod head has a diameter of a - 28 mm, and the head has a thickness of t- 10 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 105 MPa, and the bearing stress between the rod head and the support plate cannot exceed 150 MPa. Determine the maximum value of Pmax that can be supported by the structure. Support Plate Hole diameter D Rod Наad Answer in kN with 2 decimal places

The d-14-mm-diameter solid rod passes through a D-19-mm-diameter hole in the support plate. When a load Pis applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b= 11 mm. The rod head has a diameter of a - 28 mm, and the head has a thickness of t- 10 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 105 MPa, and the bearing stress between the rod head and the support plate cannot exceed 150 MPa. Determine the maximum value of Pmax that can be supported by the structure. Support Plate Hole diameter D Rod Наad Answer in kN with 2 decimal places

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The shaft shown consists of a steel tube (1) bonded to a brass core (2). The shear modulus of steel…

Q: 2. Determine the shearing stress in each of the four walls of a portion of a structural aluminum…

A: Given, Torque =3 kN-m=26.55 kip-in Dimension=100×51 mm=3.93×2 in Wall thickness=4 mm=0.15 in.

Q: 3. Determine the required diameter of the pins at A and B to the nearest 1mm if the allowable shear…

Q: Two forces P1 and P2, of magnitude P1 = 15 kN and P2 = 18 kN, are applied as shown to the end A of…

A: Given:P1=15 kN =15000 NP2=18 kN =18000 NRadius c=20 mmThe axial force and bending moment…

Q: a b 45 MPa 60° a

A: Given: Shear stress To find: Normal stress and principal stress on inclined plane

Q: Q1. C The solid 100-mm-diameter steel cantilever shaft shown in Fig. 1 is subjected to an axial…

A: To determine The state of stress at point A Principal stresses and shear stress FOS from maximum…

Q: A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is…

Q: 1) The copper pipe below has an outer diameter of 50 mm, inner diameter of 30 mm, and G = 45 GPa. It…

Q: the stress system shown, calculate the magnitude of the shear stresses on Ty and the angle a, (72…

Q: 2. In the structure below, the vertical bar A has a modulus of elasticity of 210 GPa, a length of…

Q: The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable…

A: Determine the largest torque Tmax that can be applied at the upper end of the steel rod.

Q: The bar in figure has a constant width of 30 mm and a thickness of 20 mm. Determine the maximum…

Q: Problem 5-82 The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If a torque of T = 5 kN…

A: Given:- The Am1004-T61 magnesium tube is bonded with an A-36 steel rod The magnitude of the torque…

Q: The d - 16-mm-diameter solid rod passes through a D=21-mm-diameter hole in the support plate. When a…

Concept explainers

Pressure and Stress

Question

The d-14-mm-diameter solid rod passes through a D- 19-mm-diameter hole in the support plate. When a load Pis applied to the rod, the rod head
rests on the support plate. The support plate has a thickness of b = 11 mm. The rod head has a diameter of a- 28 mm, and the head has a thickness of t-
10 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 105 MPa, and the
bearing stress between the rod head and the support plate cannot exceed 150 MPa. Determine the maximum value of Pmax that can be supported by the
structure.
Support
Plate
Hole diameter D
Rod
Неad
Answer in kN with 2 decimal places

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the maximum stress of the plate. • rivet hole diameter 2 cm • width of the plate= 7 cm • uni-axial tension of 54 MPa
Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm • uni-axial tension of 55 MPa.
10. An Assembly shown below whereas a link BD consists of a bar with 1 in. wide and 1/2 in. thick. Considering that each pin has a 3/8 -in. diameter, Find the maximum value of the average normal stress in link BD given the conditions: (a) O = 0, (b) 0 = 900. 4 kips .6 in. 12 in. 30° D
The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to 60 MPa for the bronze segment AB and 84 MPa psi for the steel segment BC. Determine the diameter of each segment so that each material is simultaneously stressed to its permissible limit when the torque T = 40 kN-m is applied as shown. The shear moduli are 35 GPa for bronze and 80 GPa for steel. Bronze Steel B A T 3 m 2 m
Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C -d₁ 40 kN -d₂. 30 kN
Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm • uni-axial tension of 55 MPa.
Question # 4: Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. Show the results in a differential element at the point. ( 2 m a 0.5m 400 KN 100 mm 300 mm 100 mm Section a-a
Q.17 The maximum bending stress is A - w/m L P Od
Mechanics of deformable bodies.
Determine the maximum stress of the plate. • rivet hole diameter 2 cm • width of the plate= 7 cm • uni-axial tension of 54 MPa
The thin rectangular plate is uniformly deformed such that Ex = 220E, Ey= -680 uE, and yy = 870 urad. If a = 35 mm, determine (a) the normal strain &, in the plate. (b) the normal strain &, in the plate. (c) the shear strain ynt in the plate. B D. a a a a a a a a a Answers: (a) En= i HE (b) Et= i HE (c) Ynt = i prad
The solid 1.85-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 925 lb/ft. Two concentrated loads also act on the rod: P= 1700 lb and Q = 1100 lb. Assume a = 20 in. and b = 40 in. Determine the normal stress in the rod at the following locations: (a) x = 13 in. (b) x = 39 in. > > > -> -> > b Answer: Ox=13in. = psi Ox=39in. = psi