Q4/ The cylindrical head of an engine is 1 m long and has an outside diameter of 50 mm. Thetemperature of outer surface is 150 °C and an ambient temperature 40 °C with a convectivecoefficient of 80 W/m².'C. The head has been provided with 12 longitudinal straight fine, whichare 0.75 mm thick and protrude 25 cm from the cylindrical surface. Calculate the heatdissipation due to addition of fines. Take thermal conductivity is 260 W/m.°C.

Given data:-Surface temperature of cylinder, Ts=150°CAmbient temperature, T∞=40°CConvective heat…

The cylindrical head of an engine is 1 m long and has an outside diameter of 50 mm. The temperature of outer surface is 150 °C and an ambient temperature 40 °C with a convective coefficient of 80 W/m?.'C. The head has been provided with 12 longitudinal straight fine, which are 0.75 mm thick and protrude 25 cm from the cylindrical surface. Calculate the heat dissipation due to addition of fines. Take thermal conductivity is 260 W/m.'C.

The cylindrical head of an engine is 1 m long and has an outside diameter of 50 mm. The temperature of outer surface is 150 °C and an ambient temperature 40 °C with a convective coefficient of 80 W/m?.'C. The head has been provided with 12 longitudinal straight fine, which are 0.75 mm thick and protrude 25 cm from the cylindrical surface. Calculate the heat dissipation due to addition of fines. Take thermal conductivity is 260 W/m.'C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Carbon steel (AISI 1010) shafts of 0.1-m diameter are heat treated in a gas-fired furnace whose gases are at 1200 K and provide a convection coefficient of 100 W/m².K. If the shafts enter the furnace at 220 K, use the lumped capacitance model to estimate how long must they remain in the furnace to achieve a centerline temperature of 800 K? Use p = 7832 kg/m³, k = 51.2 W/(mK), c = 541 J/(kg-K) and a = 1.21 x 10-5 m²/s. They must remain in the furnace for i S.
Please quick what is the answer
You are designing a small heatsink to cool a high-powered IC on a control unit PCB. The IC puts out 40,000 W/m2 and has a size of 40mm x 20mm. A fan blows 40 degrees C air across the IC at a speed of 4 m/s. The IC is well insulated on its back face. If the convection coefficient is 62 W/m2K, what is the surface temperature of the IC?
Water at 5°C is being used to cool apples from an initial temperature of 25° to 10°C. Thewater flow over the surface of the apple creates a convective heat-transfer coefficientof 15 W/(m2-K). Assume the apple can be described as a sphere with a 10 cm diameterand the geometric center is to be reduced to 10°C. The apple properties include thermalconductivity of 0.45 W/(m-K), specific heat of 3.950 kJ/(kg-K), and density of 940 kg/m3.a. Determine the time that the apples must be exposed to the water.b. If the apple is submerged only for 2 hours, what will be its center temperature?
Parvinbhai
(a) A length of brass piping is 30 m long at a temperature of 18°C. When hot water flows through it the temperature of the pipe rises to 70°C. Determine the length of the hot pipe if the coefficient of linear expansion for brass is 18 x 10-6 K-¹.
Heat transfer Calculate the heat transfer rate in Btu/hr through the pipe ona stainless steel pipe with a length of 12m has an inner diameterof 10in and an outer diameter of 13in. The temperature of theinner surface of the pipe is 50°C and the temperature of theouter surface is 48°C. The thermal conductivity of the stainlesssteel is 187 W/m-°C. Show complete solution in a clear paper.
During a wall heat flux measurement, at the instantaneous time t, we obtained the following values: Q = 30/ Tal = 20 °C Tse = 5°C Calculate the instantaneous U-Value at time t m²K (Note: R₂ = 0.13 W and R = 0.04³)
To cool hot oil, an engineer has suggested that the oil be pumped through a pipe submerged in a nearby lake. The pipe (external diameter = 15 cm) will be placed in the horizontal direction. The temperature of the outer surface of the pipe averages 125 ° C. The surrounding water temperature is assumed to be constant at 15 ° C. Pipe length 125 m. If it is assumed that there is no water movement. a. Determine the convective heat transfer coefficient of the outer pipe surface to the water. = Answer Watt / (m² ° C) b. Determine the heat transfer rate from the pipe to the water. = Answer kW
A car's rear window is defogged by the passage of hot air over its inner surface. If the hot air is at T∞, i = 40 °C and the corresponding convection heat transfer coefficient is hi = 30 W/(m²K), what are the temperatures of the inner and outer surfaces of the glass, which has 4 mm thick, if the outdoor ambient air temperature for T∞, e = −10 °C and the associated convective coefficient for he = 65 W/(m²K)?