The current-voltage characteristic/data of a silicon solar cell exposed to direct sunlight at noon in Cavite during midsummer is listed below. It is obtained by placing different-sized resistors across the two terminals of the device and measuring the resulting currents and voltages. Volts / Amps 0.000V/3.0A0.125V/3.0A0.250V/3.0A0.375V/2.5A0.500V/0.0A(a) What is the value of the short-circuit current? A(b) What is the value of the voltage at open circuit? mV(c) Estimate the maximum power that can be obtained from the device if the current starts to drop at 0.375V. mW

The current-voltage characteristic/data of a silicon solar cell exposed to direct sunlight at noon in Cavite during midsummer is listed below. It is obtained by placing different-sized resistors across the two terminals of the device and measuring the resulting currents and voltages. Volts / Amps 0.000V/3.0A0.125V/3.0A0.250V/3.0A0.375V/2.5A0.500V/0.0A(a) What is the value of the short-circuit current? A(b) What is the value of the voltage at open circuit? mV(c) Estimate the maximum power that can be obtained from the device if the current starts to drop at 0.375V. mW

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. A bank of nickel-cadmium cells is used as the emergency lighting supply for a hospital. There are 100 cells connected in series and each has an A-hr rating of 120 A-hr. The bank has to be replaced, and the manufacturer is no longer supplying nickel-cadmium cells. It is decided to replace the cells with lead-acid cells. How many lead-acid cells will be required if each has an A-hr rating of 60 A-hr, and how should they be connected?
Q2) A silicon crystal having a cross-sectional area of 0.001cm? and a length of 10 cm is connected at it's ends with 10v battery at temperature 300°K, when the current is 100mA. Find the resistivity and the conductivity? 02) Tro Fola
Given the circuit below, calculate the required Rs and the maximum power for the Zener diode. Rs(ohms), Pzm(Watts)
Please calculate the percentage of effects of electrons to conductivity of Silicon, which is 6 (ohm.m)^-1 and the mobilities are ue = 0,19m²/V.sn and up = 0,0425 m²/V.sn
If V1=26V ,v2=12V, R1=4.9k ohms , R2 =8.2k ohms, R3 = 1.4k ohms, and all diodes are silicon for the circuit below, the output voltage Vo is equal to ____ V.
Please answer only handwritten solution please And in short please
If a Si diode has a leakage current of 12 nA, k =5,800, and VD = 0.55 V, what is its ID in mA at 23oC? Express your final answer to two decimal places.
A diode network is given in Figure-1. a) Explain the tasks of the diodes (parallel and serial) and resistor in the network b) Calculate I and V. . 4Ic (mA) 30 µA +20 V 25 μΑ Si 5 20 μΑ 4 15 μΑ Ge Si 3 10 µA B 5 μΑ Ig = 0 µA 2.2 k2 10 15 20 VCE 4V Figure-1 Figure-2 2.
A three phase, 5-hp, 60Hz, 115V, 4-pole induction motor is operating at rated voltage, rated frequency, and 125 percent rated load has an efficiency of 85.4 percent. The stator conductor loss, rotor copper loss and core loss are 223.2W, 153W, and 114.8W respectively. Sketch the power flow diagram, enter the given data, and determine i) shaft speed ii) shaft torque
Draw VI characteristics of solar PV cell.
You are given a p-type doped silicon crystal and are asked to make an ohmic contact. What material would you use?
Calculate the equivalent resistances Rin of the following circuits. (The resistance value of the diodes in the conduction will be 0, the resistance value of the diodes in the insulation will be taken as infinity. R1=10ohm