The current value pass through Galvanometer is always high O can be high or low O always zero always low O

Q: Use breadboard to show this circuit. I do not know why this is not rotated.

A: The given circuit can be designed with tinker CAD software. The LED will start to glow if it is…

Q: Electrostatic Instruments has very low losses O may be used on both ac and dc O sutable for high…

A: A Brief About Electrostatic Instruments Electrostatic type of instruments uses static electric…

Q: Identify the true statement from the following statements about JFET a. It does not offer any…

A: Junction-gate field-effect transistor (JFET): This transistor is a three-terminal semiconductor…

Q: Calculate the base current for this circuit. +12V 12.5 ka 2 ka silicon Select one: a. 0.904 mA O b.…

A:

Q: If the average of set of voltage reading is 53V. The precision for one of the reading 52, will be O…

A:

Q: What is folt meter

A: In the electrical power system, the fault condition occurs when the abnormal value of the current…

Q: 17. At what anode voltage (VA) will each PUT in Figure 11–60 begin to conduct? VB +20 V VB +9 V R2…

A:

Q: finding the current and voltage (Io and vo) in polar form

A:

Q: finding the current and voltage (Io and vo) in polar form

A:

Q: The scale of a instrument is linear for DC.

A: PMMC (Permanent Magnet Moving Coil) instrument has uniform scale.  It is used for DC voltage and…

Q: For the following functions: a. Find the required Fourier Series. b. Sketch the graph of the…

A: a) To find the required Fourier Series.b) To setch the graph of the function to which the series…

Q: 120 V What is the peak secondary voltage? 10:1 transformation ratio and the diodes are silicon ellel…

A:

Q: 3V RL 5V a a1.gif d1.gif с1.gif b1.gif 立

A: In this question we will find output voltage waveform..

Q: 5. Determine the output voltage waveform for each circuit in Figures below. +10 V +10 V +10 V 3 V V…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: Three resistance 14. 5 Q, 25.5 Q and 60 Q are connected in series across 200 V. What will be the…

A: Given: Three resistances are connected in series, R1=14.5 ΩR2=25.5 ΩR3=60 Ω Supply voltage, Vs = 200…

Q: Problem #1 Consider the following waveform: Forstoff 0.3m -0.3m -1.5m -8.9m x(t) 0.9m 1.5m (a) Find…

A:

Q: Q/ Find the total current and current Armatuer and current field ? Ish 50L 50V Dz 122 A2

A:

Q: 252 2요 + Is 141 22 +.

A: Applying KCL at nodes, Node 1 V1-1412+V12+V1-V22=032V1-12V2=14121.5V1-0.5V2=70.5V1=70.5+0.5V21.5

Q: What happen if the frquency is changed from 60Hz to 50Hz?

A: Time period of a signal depends on frequency

Q: lestion 8 The correct output voltage waveform of the following clipper is 3V t. Vi RL Vo b b1.gif a…

A:

Q: In a tansistor, IC = 100 mA and IE = 100.2 mA. The value of B O50 O100 about to1 O 200

A: We can find alpha that is current gain in common base configuration by ratio of Ic to Ie and then…

Q: The potential difference is measured in .volt

A: Potential Difference:

Q: In a four-pole direct current machine

A: In a four-pole direct current(dc) machine, alternate poles are north and south.

Q: i know how to calculate Rf but you know how like the unknown has 3 spots do we calculate those 3…

A: Rf is consider as Ripple Factor which is the ratio of the rms value of AC component and the DC…

Q: Draw the output voltage waveform for the circuit in (b), and (c). and include the voltage values. R₁…

A:

Q: Find the capacitor size that wiIl make the light stay on for 10 sec after power is removed switch is…

A: The solution is given below

Q: When a 60 Hz sinusoidal voltage is applied a) to the input of a half-wave rectifier, what is the…

A:

Q: The correct output voltage waveform of the following clipper is 3V lov Vi RL Vo 5V

A:

Q: The Y axis represents the resistance. Explain in between Pt 100 and Ni 100 which one has a high…

A: In this question we need to find a which one has high sensitivity from the given graph.

Q: D +10 V R 2.0 ΚΩ Assume the diode is a practical diode with Vy= 0.7 V. If the diode is reversed, the…

A: Given circuit,

Q: 30 - In any asynchronous counter, what is the position of the counter after counting the largest…

A: Asynchronous counter :- use flip-flops which are serially connected together. What is position of…

Q: When the diac has turned on, the voltage drop across its terminals is breakover voltage required to…

A: It is given that:When the diac has turned on,the voltage drop across its terminals…