The cross-sectional area of a transformer limb is 80 cm2 and the volume of the transformer core is 5000 cm3.The maximum value of the core flux is 10 mWb at a frequency of 50 Hz. Taking the Steinmetz constant as 1.7, the hysteresis loss is found to be 100W. Determine the value of the hysteresis loss when the maximum core flux is 8 mWb and the frequency is 50 Hz.

Q: The flux linking of winding 2 if the current in the winding 1 is -4 A, and the current in winding 2…

A:

Q: An iron core is most often used in an AC transformer to 1.provide a better coupling between the…

A: An AC transformer is a device used to transfer electrical energy between two or more circuits…

Q: (b) Explain why a power transformer is ideally designed so that the flux density in the magnetic…

A: The answer is provided in the following steps.   It is best with my knowledge, please refer all the…

Q: A 800/160V, 55 HZ, 1-phase transformer with cross sectional area of the core is 26 cm? and maximum…

A:

Q: 1. In a transformer, which options are correct: A. Works on Faraday’ law and Ampere’s law B. DC…

A:

Q: A 3000/200V ,50hz. , single phase transformer has a cross sectional area of 150 cm2 for the core. If…

A:

Q: A single phase transformer with the maximum value of flux 0.0991wb and an effective cross sectional…

A:

Q: ou are employed in transformer fabrication unit. You have to design core of transformer. With regard…

A: Transformer: Transformer is an electrical static device works on the principle of electromagnetic…

Q: Question In a single-phase transformer, the total iron loss is 2500 W at nominal voltage of 440 V ar…

A: In this question We need to determine the hysteresis losses and eddy current losses at nominal…

Q: Figure Q1 shows a transformer core that has the primary winding (Np) of 500 turns and second winding…

A: A transformer core is shown with dimensions. Number of turns in the primary winding and secondary…

Q: The hysteresis coefficient of the core material of a power transformer is 110J/ m3. The eddy current…

A:

Q: It is desired to have a 4.13 mWb maximum core flux in a transformer at 110V and 50 Hz. Determine the…

A:

Q: The iron losses in a transformer core at 50 Hz are 1600 W. If the frequency is increased to 60 Hz…

A: Given, The iron losses in a transformer core at 50 Hz are 1600 W. If the frequency is increased to…

Q: When rated voltage at rated frequency is applied to a single phase transformer the hysteresis and…

A: Given, Hysteresis loss, Ph1=420 W Eddy current loss, Pe1=150 W Voltage in increased by 10%, V2=1.1…

Q: A single pahse transformer has 700 primary and 2100 secondary turns. The primary is connected to 400…

A:

Q: Usually, transformers are designed to operate with peak flux densities just below saturation of the…

A: The transformer is designed in such a way that it can act as a step-up transformer to boost the…

Q: In a single-phase transformer supply voltage 230V, 60 Hz. The supply voltage side has 500 windings…

A: According to the question we need to calculate the value of the maximum amount of flux.

Q: 1. A transformer transforms. (a) frequency (b) voltage (c) current (d) voltage and current. 2. Which…

A:

Q: We have a transformer designed to operate at 60 Hz. The voltage ratings are 4800 V rms and 240 V rms…

A: Given: A transformer is designed to operate at a frequency: f1=60 Hz New frequency is f2=120 Hz…

Q: Figure Q1 shows a transformer core that has the primary winding (Np) of 500 second winding (N,) of…

A: Introduction: A transformer is a device that steps up or steps down the level of voltage without…

Q: a) Define what the term "permeability" means. Explain why this is an important parameter in…

A:

Q: Describe the characteristics of amorphous iron that make it suitable for integrated transformer…

A: Since you have posted the multiple questions so we are supposed to answer the first one.Amorphous…

Q: A single pahse transformer has 230 primary and 870 secondary turns. The primary is connected to 400…

A: We have an Single phase transformer with, Primary Turns (N1) = 230 Secondary Turns (N2) = 870…

Q: 5- The most effective factor on the leakage inductance of an iron-cored coil is: a) The geometry of…

A: The leakage inductance of the iron cored coil is due to the fact that the primary in not properly…

Q: 4. In a transformer, which options are correct: A. Works on Faraday' law and Ampere's law B. DC…

A: Transformer is a static device the transfer electrical energy from one electrical circuit to another…

Q: current supplies hysteresis loss, in a practical transformer? a. None of these b. IM c. IC d. I0

A:

Q: A 10 transformer has 500 primary and 1200 secondary turns. The net cross-sectional area of the core…

A:

Q: step down transformer rated 2200:220 having an effective core area of 100sqcm. and has 120 turns on…

A:

Q: A 35KVA, transformer has 50 Hz frequency input with voltage values given as 300/220V, with primary…

A: It is given that: kVA=35 kVAf=50 HzV1V2=300220N1=550

Q: an ideal transformer circuit is shown in Figure Q4(a). Its primary and secondary turns are 400 and…

A:

Q: A 150 kVA, 2500/250 V, 50 Hz, single phase transformer has a no-load current of 0.75 A and a core…

A:

Q: A 50 Hz current transformer has a secondary current of 5 A, and total impedance of secondary side of…

A: Given : A 50 Hz current transformer  To find the maximum flux density in the core, ratio error and…

Q: Iron loss in a transformer: a) is dependent on load current. Ob) is a function of the resistance of…

A: Answer: is a function of eddy current and hysteresis effects in the transformer core. Explanation:…

Q: Question In a single-phase transformer, the total iron loss is 2500 W at nominal voltage of 440 V…

A: Given- A single-phase transformer, Total iron loss P1=2500 W, Voltage V1=440 V, Frequency f1=50 Hz,…

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.