The cross-section shown in Figure 3 is subjected to a moment about the X axis (M). Determine a) The principal moments of inertia for the cross-section. b) The orientation of the neutral axis.

Q: Q/Draw S and B-M D 8 kuim

A:

Q: Which of the following is considered to be an "accelerator" in an automobile? * All of them. gas…

A:

Q: Example 39: Replace the three forces shown in Fig. below, acting on the plate by a wrench. Specify…

A: When multiple forces act on an object, the resultant force is the force that creates the same…

Q: You can change any of the layer properties, including - * aut cad color only O - None of the above.…

A:

Q: What type of scale is 1:20? O Full Scale O Enlargement Scale O Reduction Scale O O O

A:

Q: NFPA diamond, red indicates the fire hazard Entropy is path function According to hazard and risk…

A: Answer is given below:

Q: The product from an open - circuit primary rod mill receiving 160 tons/hour of new ore feed joins…

A: Given:Rod mill product stream:  solids by weight.Ball mill product stream:  solids by…

Q: 1. Write 2 differences between isometric and oblique projections?

A: Dear student,                     According to the guidelines I am allowed to answer only one…

Q: What type of scale is 10:1? O Full Scale O Enlargement Scale O Reduction Scale

A:

Q: uestion 1 (: Listen Modify panel zuestion 2 Listen Paper space tab(s)

A: The Modify tools can be accessible through the keyboard, the pull-down menu, or the toolbar, as…

Q: A composite beam is fabricated by bolting two 2.3-in.-wide by 14-in.-deep timber planks to the sides…

A:

Q: Q. 8.) ZV=0 RA+RI = L0+20 +20+20 20+20 +20+20十 ZMA=0 20x3 +2OX6+20x9+20x12. +20 X 1S +20x18+20x21…

A:

Q: (a) tang tan

A: Given data: Opposite side =4 Adjacent side=2

Q: A graphical language used by engineers, draughtsman and other technical personnel Technical Writing…

A: Solution:

Q: Name the feature shown below. 10 00

A: the feature displayed in the picture is extrude

Q: OFFSET command use to draw object parallel to selected object by determine radius distance point…

A: Computer-aided drawing is the way to draw the various views of the component. In the orthogonal…

Q: Hi! This is a rather simple question, I just want to know how is h1, h2, and h3 determined? Like how…

A: The hydrostatic pressure in a liquid is calculated by the formula, P=ρgh Here, ρ is the density of…

Q: 4) FIND EGNS FOR VEM DRAW VEM DIAGRAMS 0 200 kit 30

A:

Q: In milling machine axis controls the spindle movement in the upward direction. a. Negative Y b.…

A: Milling Machine: Milling is a multi point cutting tool machining operation used for removing a layer…

Q: The part view should.com RANCES be the same CHD APPVD MIG GA as picture. 2- The color is RGB as DWG…

A: Find Draw the given object using the drawing.

Q: OA F >F>F OE- F = F, F, >F, >F, F > F, >F, D) OF> F >F,

A: Forces on the surfaces, F1,F2,F3 Area of each surfaces, 2S,S,3S

Q: I need these three parts answered (Multiple Choice). If you can not answer all three parts please…

A: Inverted section view is used on the main views of section B-B. Hence, the correct choice is (a).

Q: 14 sketch in the missing object and ce nter lines on 14

A: Given figure  To sketch the missing lines  And hidden lines

Q: DRAW THE MULTIPLE VIEW

A: The given view is in isometric view

Q: The reading of Vernier Caliper shown in the Figure is 10 30 60 70 80 1 4. 6. 7. 9. 10 .02 mm 29.54…

A: Given data: Main scale reading = 27 mm Need to determine the scale reading.

Q: if Re 77 Soo %3D 등 = \ , * 103 Determine f %3D from mod'] chart.

A:

Q: The part view should be the same as picture. 2- The color is RGB as 0,220,100. 3- Should use the…

A: Find Draw the given object using the drawing.

Q: The following was recorded from the chiller at the BYU-Idaho Central Energy Facility. Atmospheric…

A:

Q: What type of scale is 1:1? Full Scale O Enlargment Scale Reduction Scale

A: Scale factor is the ratio of the length of the drawing to the actual length of the object. The scale…

Q: Draw the multiple view

A: Given isometric view

Q: Name the feature shown below.

A: The given figure is of

Q: 2. Draw the auxiliary view of the orthographic views above.

A:

Q: A00007: Drafting Competencies - To create drawing view B' it is necessary to select drawing view 'A'…

A: Break view in the solidworks is used to display the larger drwaing in smaller drawing sheet by…

Q: 1. What are the properties of natural gas? 2. Outline the difference between non associate and…

A: (1)

Q: -30- R-64 20 -10 (5.0) -50 -40 -30 -20 -10 10 10-

A: given:

Q: How did you get the Tsat values

A: This question is based on the properties of water at different temperatures and pressure.

Q: A saw its angular velocity when work is 1500rpm when its stopes by magantic brake it needs 1 min to…

A:

Q: ers O way of telng ems the following practical tests end C plus collect data. al investigation and…

A: Hi and thank you for the questions. Since you have asked multiple questions, as per our honour code…

Q: LESSON: AUTODESK FUSION 360 Identify the feature displayed in the picture, and choose from choices…

A: Identify the feature displayed in the picture, and choose from choices below.

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.