The crate in an inclined plane (angle of inclination, 02=10°), has a mass M=200 kg and is subjected to a towing force P acting at an angle e1=20° with the horizontal. If the coefficient of static friction is 0.2, determine the magnitude of P to just start the crate moving down the plane. (A) N=1909 N, P=47 N (B) N=1687 N, P=39 N N=1658 N, P=37 N N=1780 N, P=52 N

The crate in an inclined plane (angle of inclination, 02=10°), has a mass M=200 kg and is subjected to a towing force P acting at an angle e1=20° with the horizontal. If the coefficient of static friction is 0.2, determine the magnitude of P to just start the crate moving down the plane. (A) N=1909 N, P=47 N (B) N=1687 N, P=39 N N=1658 N, P=37 N N=1780 N, P=52 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Current Attempt in Progress Construct the shear-force diagram and identify the largest negative shear force. Assume a = 4.5 ft, b = 9.0 ft, c = 18.0 ft, w = 1170 lb/ft, and P = 3200 lb. P B C D a b. Answer: Vmin lb Save for Later Attempts: 0 of 1 used Submit Answer
R= 9 A three span continous beam ABCD is loaded with ultimate loads as shown in Figure 3. Determine the required plastic moment of resistance assuming uniform section of beam. Assume, p = (25+ R/10) kN, q = (20 + R/5) kN. 10 kN/m L mám D A B 5m 2m Figure 3 2m 3m 2m
3. A 100-kg crate is being pushed by a horizontal force F, with a magnitude defined by the second degree curve below. If the coefficients of static and kinetic friction between the crate and the surface are µ; = 0.2 and ps = 0.10, respectively, determine the total time it takes for the force to move the crate 50 m from its initial position. F F=kr 500N F 2s
The 3-kg rod OA is initially hanging in a vertical position when a 0.6-kg block B, sliding on a horizontal surface with negligible friction with a velocity of VBO-3.2 m/s, strikes the rod at its end A. 0 VBO B 1. If the block's velocity after impact is VBI =0.16 m/s to the left what is the coefficient of restitution, e, between block B and bar OA? 2. What is the impulse exerted by rod OA on block B? 0.3 m 0.9 m
The floor system of a residential building consists of 125mm thick reinforced concrete slab (unit weight = 23.6 KN/m^3) resting on three 8m spanned RC floor beams spaced at 3.2 meters on centers. Size of RC beam is 200mm x 450mm. NSCP 2015 Load factors: 1.2DL & 1.6LL. Assume simple supports. Calculate the unfactored beam self-weight in KN/m? Express your answer in 2 decimal places.
A rectuangular wooden beam ( fb = 7.0 MPa, E = 12.9 GPa) ha s across-sectional area of300 mm by 600 mm. The beam has a simple span of five meters. A vibrating machine weighing800 kg is located at the midspan. The machine is working under a constant force of 500 N andaccidentally stopped after 0.7 sec (rectangular pulse). Determine the following:Stiffness, ? = _____________________Angular natural frequency, ?? = _________________ Displacement at t = 0.7 seconds ?(? = 0.7) = _______________________Displacement at t = 1.5 seconds ?(? = 1.5) = _______________________(???)? = _______________
Reinforced Concrete Civil Engineering
3. Determine the coefficient of static friction for the 200 kg block which starts to slide at the critical inclination of 32°. Suggest a possible combination of surfaces that have such a coefficient of static friction. g sin
Prob. 4 Consider a slender 2 meter uniform homogeneous 7-kg bar that rests on, and makes 45-degree angles with, a smooth vertical wall and a rough horizontal floor. What is the minimum coefficient of friction required to prevent the bar from slipping?
Two large fixed parallel planes are 240 mm apart. The space between the surfaces is filled with oil of viscosity 0.81 N.s/m2. A flat thin plate 0.5 meter square area moves through the oil at a velocity of 0.3 m/s. calculate the drag force: A] When the plate is equidistant from both the planes, and B] When the thin plate is at a distance of 80 mm from one of the plane surface.
I. Single-choice questions.: 5. Bridge piers belong to which part of a bridge? ( ) A. Bridge superstructure B. Bridge substructure C. Bridge deck system D. Bridge foundation 6. When calculating the load transverse distribution coefficient (m) near the bearing supports of a simply-supported beam bridge, which kind of calculation method is recommended? ( ) A. Lever principle method B. Hinge joint slab method C. Eccentric compression method D. G-M method
1. A bundle is projected 10 m upward on a 0.26 rad inclined plane so that it reaches the top of the plane with zero velocity. Knowing that the coefficient of kinetic friction between the package and the incline is 0.08, determine (a) the initial velocity of the package at A, (b) the velocity of the package when it returns to its original position.