The Crate has a weight of 550 lb. The tension in the cord AC is nearly_ B 30 D lb.

Q: The boom shown has a negligible weight and supports the 1000 N load. А 60° 1000 N 7.1 Find the…

A:

Q: Find the magnitude of all the elements and tell whether they are in tension or compression.

A:

Q: The 500-kg crate is supported by the three cables. Find the tension in cables AD, BD and CD.

A:

Q: Find the tension in leg AC of the cable if the sag, h = 4'. 3' h

A:

Q: The plate shown carries a load of 10 kN applied at point E, and is-supported in a horizontal…

A:

Q: 5 m 3 m A 8 m D D 40 KN 20 kN 8 m C

A:

Q: Find the  weigh W of the block .the system is in equilibrium

A:

Q: The cylinder have equal diameter. Solve for the reactions at A, D and C.

A: Given Cylinder weight 20 kN 40 kN 30 kN To find Reaction at A, D and C

Q: Find the maximum weight of the flowerpot that can be supported without exceeding a cable tension of…

A:

Q: Find tension in the cable

A: Given data ; Acc. to question the free body diagram, W=981 Nμ=0.2 AForce=100 N

Q: The ring supports the 1000-N load and is held in position by the two cables attached to vertical…

A: Calculate the angles formed between tensions T1 and T2 and their inclination with x-axis using the…

Q: The homogeneous 200-lb sign is suspended from three wires. Find the tension in each wire.

A: Weight is 200lb  sinθ=45  cosθ=35. ∑Fy=0 T1 is completely horizontal and Due to symmetry  T2=100 lb…

Q: E 3 D. 12 5 A B

A: As we know that the weight always acts at the downward to the body and as the wall is smooth no…

Q: If the plate is to remain in equilibrium, find the tension for all the three cable that supports the…

A: Free body diagram of the load is shown in the figure. Dimensions of the plate are as shown in the…

Q: As shown by this image, the chandelier is supported by several ropes and is in equilibrium. Cable BC…

A: Given data: The angle θ=31°. The maximum tensile force in the rope is Fmax = 410 lb.

Q: Spring data Туре Helical squared and ground ends Initial Compression of spring 10 mm 70 mm Further…

A: x0= 10 mmxf=70 mmτ=1500 Nmm2G=72000 Mpad= 6mm c=Dd=4 ⇒D=24 mm kw=4×4-14×4-4+.6154kw=1.4037

Q: H. 0.5 ft Determine Ax, Ay and Tension at C 0-30 108 lb

A:

Q: THE 600 lb CRATE IS SUPPORTED BY THE THREE CABLES. FIND THE TENSION IN EACH CABL

A:

Q: 2. Cable AB passes over the small ideal pulley C without a change in its tension. The length of…

A: Given data Weight of load W = 50N To determine the tension in the cable CD

Q: The baloon is in balance with 3 ropes. If each of the rope can stand to 500N tensile force, find the…

A: It is given that the maximum force that the rope supports is not greater than 500 Newton.   Also, it…

Q: The homogeneous 100-kg sign is suspended from three wires. Find the tension in each wire.

A: Given Mass = 100 kg To find Tension on the strings

Q: 02 3 Ze. ww o9

A: GIVEN:

Q: Two men carry a load of 2 kN by means of two ropes fixed to the weight. One rope is inclined at…

A: Answer : Given parameters Weight = 2KN Inclination of rope 1 = 45o  with vertical Inclination of…

Q: 30 2f- 6 ft-

A:

Q: Find the tensian focce in each cable.

A:

Q: The 400-kg precast concrete section is hoisted by a vertical force 'T' from a crane. Find the…

A: Calculate the vectors AB, AC and AD.…

Q: The 500-kg crate is supported by three cables. Find the tension in cable AD.

A: The coordinates of the points, The weight of the box,

Q: 200 N 6. 15 E= 100 6pa V= 0.a5 0:5 m

A:

Q: Find the deformation and the reaction at A and B.

A: Given: Youngs modulus→E=2×104 MPa Cross sectional area of block AC→A1=220 mm2 Cross sectional area…

Q: In the 4-cable setup, find the tension in each cable to maintain the equilibrium of the system

A: given; In the 4-cable setup, find the tension in each cable to maintain the equilibrium of the…

Q: y A(1,3,0) C (4,3,0) D(2,0,-1) 80 kg B(3,3,-4) X

A:

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.