• The cost of a 1-o overhead feeder is OMR 6 a per km ( a is area of cross section in sq mm) and the interest and depreciation charges on feeder are 10%. Determine the most economical current density to use for transmission requiring full load current for 50% of the year. The cost of generating electrical energy is 10 baisa per unit. Assume resistance of 1 m length and 1 mm? section of conductor as 1/58 ohm.

• The cost of a 1-o overhead feeder is OMR 6 a per km ( a is area of cross section in sq mm) and the interest and depreciation charges on feeder are 10%. Determine the most economical current density to use for transmission requiring full load current for 50% of the year. The cost of generating electrical energy is 10 baisa per unit. Assume resistance of 1 m length and 1 mm? section of conductor as 1/58 ohm.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a.Why does power plants have high amounts of voltages? Explain. b.Is it safe for transmission lines to have high current instead of high voltage? Why? c.What phenomenon is avoided by having separations between three conductor phases? Explain this phenomenon.
Each line of a 3-phase system given in figure is suspended by a string of 5 identical disks and the ratio of C1/C=0.1 (Shunt capacitance per self-capacitance) is given. If the string is connected to line of voltage 33kV. a) What is the voltage distribution over the unit of string and what is the string efficiency? b) When the string is supplied by a Guard Ring and this lead to add a two air capacitance of value 0.2C, 0.1C respectively to the nearest to the conductor. Find the new voltage distribution and the new efficiency.
O List any three factors to be considered for mechanical design of overhead lines (i) An overhead transmission line is supported at a river crossing by two towers of height 38 m. The weight of the conductor is 0.307 kg/m. The weight due to wind is 1.4 kg/m. The ultimate strength is 1100 kg and factor of safety is 2. If the Span length is 140 m. Determine (a) Total weight of the conductor (. (b) Sag ( (c) Total Length of conductor between supports (d) Clearance between the lowest point on the conductor and water level.. Total Weight of the conductor Sag Total Length of the conductor between the supports Clearance between the lowest point on the conductor and water level
Solve showing all the steps in detail
1. A single-phase power system as shown in Figure 1 consists of a 240 V, 60 Hz generator supplying a load, Zod = 8 + j6 Q through a transmission line of impedance, Zne = 0.08 + j0.14 Q. Answer the following questions: (1) transformer, T; and T2. Determine the voltage at the load and transmission line losses without the (ii) Determine the voltage at the load and transmission line losses with the transformer, T, and T2. T1 T2 1:10 10:1 IG Zaine Zioad source Figure 1
The Cost OF Single phase overhead feeder is OMR q Per KM(a is area of cross section in sq mm) and the intrest and depre Ciation Chargs onfeeder omical carrent density are 7Y. defermain to use for the most econor requiring Full load current of 27% of the 12 baisa is year. The Cost per unit ass ume resistance of Im lenahth length and I mm² secfion of Conductor as 1/32 find Current densi ty =?
A 115 kv line has a horizontal configuration. The distance between adjacent conductors is 9ft. What is the geometric mean distance of the line?
According to OES4, The Voltage Drop Tolerance limit for 3 Phase 4 Wire System with power circuit is----- a. 9.60V b. 7.20V c. 12.45V d. 16.60V
Determine the best current density in A/mm² for a 3-0 overhead line if the line is in use for 2500 hours per year and if the conductor costing Rs 3 per kg has a specific resistance of 1.73 92 m and weighs 6200 kg/m³. Cost of energy is 10 P/unit. Interest and depreciation is 15% of conductor cost.
Question 1) A 154 kV transmission line has a length of 100 km. The line and the conductors are given in Figure 1. The line is operated at f= 50 Hz. For both old and new lines calculate; a. GMD and GMR. b. Inductance of the line in Henries (H). c. Series Impedance (Z) of the line in Ohms. d. *Compare the results for both lines and comment on the results. e. *If the distance between the two neighbouring conductors is increase from 13 meters to 15 meters what would be the parameters in part a.,b. and c. comment on the results. New Line's Conductors 13 m 13 m Old Line's Conductors d r = 2 cm d = 40 cm r = 2 cm Figure 1
The cost of a single phase overhead feeder is OMR 17 a per km (a is area of cross section in sq mm) and the interest and depreciation charges on feeder are 7%. Determine the most economical current density to use for distribution requiring full load current of 70% of the year. The cost of generating electrical energy is 12 baisa per unit. Assume resistance of 1 m length and 1 mm section of conductor as 1/62 ohm. Current density =- A/mm?
1.9II Q.32: For the equivalent circuit of lossless linear + reel- 9:1 transformer shown, find the value of L. L2. M & k? Vi 8.1II (Ans.: L1=10H, L2=0.1H, M=0.9H & k=0.9) Jideal reel