The conditions at the beginning of compression in an Otto engine operating on hot- air standard with k = 1.34, are 101.3 kPa, 0.038 m and 32°C. The clearance is 10% and 12.6 kJ are added per cycle. Determine: a) V2, T2, P2, T,, P3, T,, and P, b) W c) e d) Pm

The conditions at the beginning of compression in an Otto engine operating on hot- air standard with k = 1.34, are 101.3 kPa, 0.038 m and 32°C. The clearance is 10% and 12.6 kJ are added per cycle. Determine: a) V2, T2, P2, T,, P3, T,, and P, b) W c) e d) Pm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An Ideal Otto engine, operating on the hot-air standard with k=1.34, has a comperession ratio of 5. At the beginning of compression the volume is 6 cu ft, the pressure is 1375 psia and the temperature is 100 degrees Farehnheit. During the constant-volume heating, 340 Btu are added per cycle. Find A)c, b) T3 c)P3 and e) Pm
Problem 1) Rankine Cycle Analysis Consider a simple Rankine cycle, steam power plant. The state points are defined in the schematic and the operating conditions are given in the Table la. The steam flow rate is 137.4 lbm/s. You may use "EES," but supply your code. a) Provide a quantitative T-s diagram including all state points, lines of constant pressure, and the "dome." b) Determine all the energy quantities and complete Table 1b. Discuss the value of the quality at state 4. c) Determine all the exergy quantities and complete Table 1c. Assume the dead state temperature is 77°F and the dead state pressure is 14.7 psia. d) Discuss your results. What additional insights does the exergy analysis provide? 3 Quoiler 4 Fuel State 1 2 3 4 State 1 2 3 4 State br (Btu/lbm) 1 ? 2 ? Boiler ? ? Table 1a: State Points and Other Items T (°F) p (psia) Variable ? 0.71 XI ? 700 turbine 1057 700 pump ? 0.71 boiler T (°F) p (psia) ? 0.71 Turbine ? 1057 ? Condenser Table 1b: Energy Results 700 700 0.71 W…
6.) Air undergoes Isothermal expansion in a Carnot cycle where the pressure decreases from 2.5 MPa to 1.5 MPa. This process has a temperature of 550 K and it decreases to 400 K before the Isothermal compression stroke. Find a.) Qa, b.) Qr, c.) Wnet (kJ/kg), d.) the efficiency (%), e.) draw the T-S diagram with proper label of points, and f.) the pressures before and after Isothermal compression • 71.55 kJ/kg, 61.78 kJ/kg, 9.77 kJ/kg, 13.65%, 251.52 kPa and 502 kPa • 80.66 kJ/kg, 58.66 kJ/kg, 22 kJ/kg, 27.27%, 492.08 kPa and 820.13 kPa 61.22 kJ/kg, 41.22 kJ/kg, 20 kJ/kg, 29.98%, 315.1 kPa and 795.55 kPa 1000 kJ/kg, 900 kJ/kg, 100 kJ/kg, 10%, 500 kPa and 1000 kPa
Need help with this homework problem. At the beginning of the compression process of an air standard Otto cycle, p1 = 1 bar, T1 = 300 K. The maximum temperature in the cycle is 2250 K and the compression ratio is 9.8. The engine has 4 cylinders and an engine displacement of Vd = 2.1 L. Determine per cylinder: a) the volume at state 1 in L.b) the air mass per cycle.c) the heat addition per cycle, in kJ.d) the heat rejection per cycle, in kJ.e) the net work per cycle, in kJ.f) the thermal efficiency.g) the mean effective pressure, in bar.h) Develop a full exergy accounting per cycle, in kJ. Let T0 = 300 K, p0 = 1 bar.i) Devise and evaluate the exergetic efficiency for the cycle.
An air-standard dual cycle has a compression ratio of 9.1 and displacement of Va= 2.2L.At the beginning of compression, p1= 95 kPa, and T = 290 K. The heat addition is 5 kJ, with one quarter added at constant volume and the rest added at constant pressure. Determine: a) each of the unknown temperatures at the various states, in K. b) the net work of the cycle, in kJ. c) the power developed at 3000 cycles per minute, in kW. d) the thermal efficiency. e) the mean effective pressure, in kPa. Step 1 Your Answer Correct Answer (Used) Determine each of the unknown temperatures at the various states, in K. 684.1 K T3 = K 1217 T4 = 2311 K 1440 K Step 2 X Your answer is incorrect. Determine the net work of the cycle, in kJ. Weycle = I 3.470026652 kJ Hint Save for Later Attempts: 1 of 3 used Submit Answer Step 3 The parts of this question must be completed in order. This part will be available when you complete the part above.
At the beginning of the compression process of an air standard Otto cycle, p1 = 1 bar, T1 = 300 K. The maximum temperature in the cycle is 2250 K and the compression ratio is 9.8. The engine has 4 cylinders and an engine displacement of Vd = 2.1 L. Determine per cylinder: a) the volume per cylinder at state 1.b) the air mass per cycle.c) the heat addition per cycle, in kJ.d) the heat rejection per cycle, in kJ.e) the net work per cycle, in kJ.f) the thermal efficiency.g) the mean effective pressure, in bar.h) Develop a full exergy accounting per cycle, in kJ. Let T0 = 300 K, p0 = 1 bar.i) Devise and evaluate the exergetic efficiency for the cycle. Correct Answers for a, b, and c. v1= 0.585 L m = 0.000679 kg Qin = 0.942 KJPlease shows correct solutions. Thank you!
A. Discuss how the (Cetane & Octane ) numbers are affected by the following engine parameters: А. 1) Ignition delay 2) Method of injection 3) Engine Design 4) Compression ratio 5) Type of ignition 6) Flame speed В. Discuss Why? 1) The two-stroke cycle engine must always have an intake pressure boost. 2) In compression ignition engines, no fuel is added to the incoming air, so that compression is done on air only. 3) In two- stroke SI engines, scavenging lasts until piston passes BDC and closes intake and exhaust ports. 4) In Dual cycle, combustion occurs once at constant volume and continued at constant pressure.
I only need help with filling in the answers for parts h and i. At the beginning of the compression process of an air standard Otto cycle, p1 = 1 bar, T1 = 300 K. The maximum temperature in the cycle is 2250 K and the compression ratio is 9.8. The engine has 4 cylinders and an engine displacement of Vd = 2.1 L. Determine per cylinder: a) the volume at state 1.b) the air mass per cycle.c) the heat addition per cycle, in kJ.d) the heat rejection per cycle, in kJ.e) the net work per cycle, in kJ.f) the thermal efficiency in %.g) the mean effective pressure, in bar.h) Develop a full exergy accounting per cycle, in kJ. Let T0 = 300 K, p0 = 1 bar (See image below).i) Devise and evaluate the exergetic efficiency for the cycle. part h
Hello, this is the problem attached below: An air-standard dual cycle has a compression ratio of 8.6 and displacement of Vd = 2.2 L. At the beginning of compression, p1 = 95 kPa, and T1 = 290 K. The heat addition is 4.75 kJ, with one quarter added at constant volume and the rest added at constant pressure. Determine: a) each of the unknown temperatures at the various states, in K.b) the net work of the cycle, in kJ.c) the power developed at 3000 cycles per minute, in kW.
I only need help with parts f to i. At the beginning of the compression process of an air standard Otto cycle, p1 = 1 bar, T1 = 300 K. The maximum temperature in the cycle is 2250 K and the compression ratio is 9.8. The engine has 4 cylinders and an engine displacement of Vd = 2.1 L. Determine per cylinder: a) the volume at state 1.b) the air mass per cycle.c) the heat addition per cycle, in kJ.d) the heat rejection per cycle, in kJ.e) the net work per cycle, in kJ.f) the thermal efficiency in %.g) the mean effective pressure, in bar.h) Develop a full exergy accounting per cycle, in kJ. Let T0 = 300 K, p0 = 1 bar.i) Devise and evaluate the exergetic efficiency for the cycle.
Consider an air standard Diesel cycle. At the beginning of compression, the compression is 300 K and the pressure is 101.35 kPa. If the compression ratio is 15 and during the process 1860 kJ/kg of air is added as heat. Calculate the mean effective pressure. a.) 1300 kPa b.) 1500 kPa c.) 1700 kPa d.) 1900 kPa e.) None of these
I only need help with parts g to i. At the beginning of the compression process of an air standard Otto cycle, p1 = 1 bar, T1 = 300 K. The maximum temperature in the cycle is 2250 K and the compression ratio is 9.8. The engine has 4 cylinders and an engine displacement of Vd = 2.1 L. Determine per cylinder: a) the volume at state 1.b) the air mass per cycle.c) the heat addition per cycle, in kJ.d) the heat rejection per cycle, in kJ.e) the net work per cycle, in kJ.f) the thermal efficiency in %.g) the mean effective pressure, in bar.h) Develop a full exergy accounting per cycle, in kJ. Let T0 = 300 K, p0 = 1 bar.i) Devise and evaluate the exergetic efficiency for the cycle.