The compound beam is pin jointed at A and simply supported at B. The distributed load (rectangular distribution q N/m over the length 2a and triangular distribution over the length a) acts upwards. Find the reactions at pin joint A and simple support B. A 2a q N/m B a

The compound beam is pin jointed at A and simply supported at B. The distributed load (rectangular distribution q N/m over the length 2a and triangular distribution over the length a) acts upwards. Find the reactions at pin joint A and simple support B. A 2a q N/m B a

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.20P: A plane Frame is restrained at joints A and D, as shown in the figure. Members AB and BCD are pin...

See similar textbooks

Related questions

Q: The yield strength of a brass alloy that has an average grain diameter of 0.01 mm is 150 MPa. The…

Q: The two blocks A and B each have a mass of 400 g. The blocks are fixed to the horizontal rods, and…

A: M=(2t+sin(at) ) N.ma= 5 rad/secV1 = 2 m/sm = 0.4 kgt= 3 secV2=?

Q: Parvinbhai

A: The objective of the question is to determine the principal stresses and the maximum shearing stress…

Q: The bent rod is supported at A. B, and C by smooth journal bearings as shown in (Egure 1)

Q: Problem 2.132 The end B of a robot arm is moving vertically down with a constant speed vo= 2 m/s.…

A: v0=2 m/sd=1.5 mthe free body diagram:

Q: A ramjet is traveling at Mach 3 at an altitude of 4572 m, the external static temperature is 258.4K,…

A: Given data:Flight Mach number (M) = 3Altitude (h) = 4572 mExternal static temperature (T0) = 258.4…

Q: Pin A is fixed to the disk. Link BC has a constant angular velocity of 5 rad/s CCW. Given that R =…

A: Given:The constant angular velocity of link BC, The radius of the disk, The value of the length

Q: A circular plate with weight W-180 k lb acting at its center, point F, is supported by cord DE and a…

A: To findDetermine the cable tension for the circular plate.Givencircular plate weight,

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: The angular velocity of AB is (constant)

Q: Air is flowing in a duct as shown in the figure below. A Pitot-static tube and a thermocouple are…

A: Given ,

Q: Consider an offset inverted four-bar slider crank mechanism as shown in the following figure.…

Q: 2.2 An air-standard Dual cycle has a compression ratio of 10. The pressure and temperature at the…

Q: negligible. Determine the safety factor against yield using Coulomb-Mohr failure theory

A: Calculate the normal bending stress at A.

Q: - The square plate is deformed into the shape shown by ormal strain along diagonal AC and the shear…

A: Calculation for normal strain in AC

Q: The initially stationary 11-kg block is subjected to the time-varying horizontal force whose…

A: The mass of block is

Q: Parvinbhai

Q: Determine the general expression for the moment of F about (a) point B and (b) point O. The moments…

Q: 6.113 A car's double-wishbone suspension is shown. The shock absorber BC is pinned at B and C. The…

A: The force F is

Q: The crank OA rotates in the vertical plane with a constant clockwise angular velocity wo of 2.1…

Q: Parvinbhai

A: The objective of the question is to determine the static temperature, static pressure, and flow…

Q: A laminated semi-elliptic leaf spring under a central load of 3000 lb is to have an effective length…

Q: 3. The pendulum, which consists of the 4-ft light rigid bar and the 14-lb cylinder A, is released…

Q: Q.2) For the figure shown, if a load P₁ = 120 kN at A and load P₂ 100 kN is uniformly distributed…

A: Given:Find:Poisson's ratio for the pipe material.

Q: Consider the pipe assembly in (Figure 1). F₁ = {30i +40j-30k) N. F2 = {601 - 10j-15k} N. Figure 0.8…

A: The force applied is

Q: Required information Problem 08.041-Determine the principal stresses for the circular cross section…

Q: A four stroke gas engine develops 4.2 kW at 180 r.p.m. and at full load. Assuming the following…

Q: Learning Goal: To he able to use Mohr's circle to find the nrincinal Figure h X 1 of 1 > Review An…

A: The moment of inertia and product of inertia about the centroidal axis.Given:The dimensions of the…

Q: Piston P is moving upward with a velocity of up = 260 in./s (Figure 1) Determine the velocity of the…

A: The velocity of piston is The angle is

Q: Consider a forced vortex in water (density is p = 1000 kg m-³), where the velocity components are…

Q: Determine the area moments of inertia Ix and ly. Given that c= 16 mm. (Round the final answers to…

A: Write the given data.

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: As shown in the figure below, water behind a dam enters an intake pipe at a pressure of 24 psia and…

A: The diameter of exit pipe is The acceleration due to gravity is .The specific volume is The cost of…

Q: Required information steady A bar of steel has the minimum properties Se=40 kpsi, Sy= 60 kpsi, and…

Q: 3. 1500 N The rod below has a diameter of 40mm. Find the stresses acting at point A. Hint: draw 3…

Q: 3. Consider a freely falling film of thickness h. Assume that the flow is steady, fully developed,…

A: For the solution refer below images.

Q: Problem 5: The forked rod is supported by a collar at A, a thrust bearing at B, and a cable CD.…

Q: A 100 mm diameter shaft is subjected to a 10 kN.m bending moment and an axial tension force of 150…

Q: 6) Assume that an operator is drilling with holes, equally spaced in a bolt-hole circle, i.e., there…

A: Calculation of tolerance between hole centers:Given data:Diameter of bolt hole circle = 6 inNumber…

Q: 1. Four rigid bodies are connected by 5 springs as shown in the figure below. Rigid while 1, 2, and…

A: The spring constant value are Point is fixed

Question

Parvinbhai

The compound beam is pin jointed at A and simply supported at B. The distributed load
(rectangular distribution q N/m over the length 2a and triangular distribution over the length
a) acts upwards. Find the reactions at pin joint A and simple support B.
A
2a
q N/m
B
a

AI-Generated Solution

AI-generated content may present inaccurate or offensive content that does not represent bartleby’s views.

Unlock instant AI solutions

Tap the button
to generate a solution

Click the button to generate
a solution

SEE SOLUTION

Similar questions

Beam ABC is supported by a tie rod CD as shown. Two configurations are possible: pin support at A and downward triangular load on AB or pin at B and upward load on AB. Which has the larger maximum moment? First, find all support reactions; then plot axial force (N), shear (V), and moment (M) diagrams for ABC only and label all critical N, V, and M values. Label the distance to points where any critical ordinates are zero.
Beams ABC and CD are supported at A,C, and D and are joined by a hinge (or moment release) just to the left of C. The support at A is a sliding support (hence reaction A = 0 for the loading shown below). Find all support reactions; then plot shear (F) and moment (M) diagrams. Label all critical Fand M values and also the distance to points where either F and/or M are zero.
Find support reactions at 4 and Band then use the method of joints to find all member forces. Let b = 3 m and P = 80 kN.
Find support reactions at A and D and then calculate the axial force N, shear force V, and bending moment M at mid-span of AB. Let L = 14 ft, q0 = 12 lb/ft, P = 50 lb. and = 300 lb-ft.
Repeat Problem 9,5-15 for the anti-symmetric loading shown in the figure.
A temporary wood flume serving as a channel for irrigation water is shown in the figure. The vertical boards forming the sides of the flume are sunk in the ground, which provides a fixed support. The top of the flume is held by tic rods that are tightened so that there is no deflection of the boards at that point. Thus, the vertical boards may be modeled as a beam AB, supported and loaded as shown in the last part of the figure. Assuming that the thickness t of the boards is 1,5 in., the depth d of the water is 40 in., and the height h to the tie rods is 50 in., what is the maximum bending stress in the boards? Hint: The numerically largest bending moment occurs at the fixed support.
Repeat Problem 6.2-1 but now assume that the steel plate is smaller (0.5 in. × 5 in.) and is aligned with the top of the beam as shown in the figure.
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
The plane frame shown in the figure is part of an elevated freeway system. Supports at A and D arc fixed, but there are moment releases at the base of both columns (AB and DE) as well as in column BC and at the end of beam BE. Find all support reactions; then plot axial-force (N), shear (F), and moment (M) diagrams for all beam and column members. Label all critical N, V, and M values and also the distance to points where any critical ordinatcs are zero.
The Z-section of Example D-7 is subjected to M = 5 kN · m, as shown. Determine the orientation of the neutral axis and calculate the maximum tensile stress c1and maximum compressive stress ocin the beam. Use the following numerical data: height; = 200 mm, width ft = 90 mm, constant thickness a = 15 mm, and B = 19.2e. Use = 32.6 × 106 mm4 and I2= 2.4 × 10e mm4 from Example D-7
The continuous frame ABC has a fixed support at A, a roller support at C, and a rigid corner connection at B (see figure). Members AB and BC each have length L and flexural rigidity EL. A horizontal force P acts at mid-height of member AB. Find all reactions of the frame. What is the largest bending moment Mmaxin the frame? Note: Disregard axial deformations in member AB and consider only the effects of bending.
A simply supported beam ABC is loaded at the end of a bracket BDE (see figure). Draw axial-force, shear-force, and bending-moment diagrams for ABC.