The compound bar is composed of brass and copper. It supports the axial loads shown below. Determine the stresses developed on both materials. Indicate whether the stress is tensile or compressive Answer: Obr oco = Brass d-6.5 inches 2016 Copper d-4.5 inches 250 lb

Q: A metal rod that is 12.0 m long and 0.74 cm2 in cross-sectional area is found to stretch 0.27 cm…

A:

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A: Calculate the stress in steel section.

Q: i need to know how they got the value of 52.89 from the eqaution

A: Given Data : Y = 1.12 a = 0.1 mm = 10-1 mm  K1c = 1.05MPa.m0.5 To Find :  Part (b) how to get the…

Q: The beam is supported by a pin at C and an A- 36 steel guy wire AB. If the wire has a diameter of…

A: Solution:-Given thatDiameter of the wire (d)=0.2 inuniformely distributed load (w)=1000 lb per ft

Q: Using the method of joints, determine the magnitude of force (Ib) in member BC of the truss shown if…

A: In this question we have to use the method of joints and we have to determine the magnitude of force…

Q: Find the stresses in members BC, BD, and CF for the truss shown in Indicate the tension or…

A:

Q: A hollow bar with an outer diameter of 25 mm and an inside diameter of 18 mm carries a tensile load…

A: Tensile load = 100kN Outer diameter D1 = 25 mm inner diameter D2= 18 mm

Q: 1) What is the deformation 8ag in mm? 2) What is the deformation đạc in mm? 3) What is the…

A: Dear Student According to Bartleby guidelines I will only solve 1st question's three subparts. If…

Q: Determine the largest weight W that can be supported by two wires shown in Fig. The stress in either…

A: Maximum weight supported by the given system of wires is equal to the sum of vertical components of…

Q: Assume a hand has a 1.4m shaft of bone with an average cross-sectional area of 3 [cm] ^2. What is…

A:

Q: A steel bar is 10 mm in diameter and 2 m long. It is stretched with a force of 20 kN. Calculate the…

A: Given data: Diameter (d) = 10 mm = 0.010 m Length = 2 m Force (F) = 20 kN = 20 × 103 N Required: The…

Q: Find the modulus of elasticity of a cast iron rod of diameter 20 mm and length 250 mm subjected to a…

A: Diameter of rod = 20 mm So, radius, r = 10 mm = 10-2 m Length of rod, L = 250 mm = 0.25 m Tensile…

Q: Why R_[Ay) is calculated here? Explanation required

A: Step 1:Given data:A=6 mm2P=1.8 KNStep 2:Here A and B are left, right nail and RA,RB are reaction…

Q: Example: A lever is keyed to a shaft 38mm diameter (Ø) the width of the key is 13mm and its length…

A: a = 0.915 m d = 38 mm = 3.8 cm = 0.038 m r = d2 = 3.82 = 1.9 cm = 0.019 m w = 13 mm = 0.013 m l = 50…

Q: Members AB and BC can each support a maximum compressive force of 730 lb, and members AD, DC. and BD…

A: in this question  we draw free body diagram of point A and point D . then we get equation  x and y…

Q: A Strain Strain Stress Stress B.

A: Correct option is A  i e material A is stronger than B .

Q: A steel rod 250 mm long is subjected to a tensile stress. If its change in length is 1/40 mm, what…

A: Given: Steel rod length, L=250 mm Change in length, ∆L=140 mm Steel Young's Modulus, γ=2×105 N/mm2…

Q: A vertebra is subjected to a shearing force of 510 N. Find the shear deformation, taking the…

A: Solution: Given that Shearing force = 510 N vertebra = 3 cm diameter = 4 cm shear modulus = 8x1010…

Q: 1. Calculate the elongation of the cable due to load, if a steel cable of 4cm diameter is used to…

A:

Q: What is the stress for a wire of 5 m long so that the strain is 2% of 0.2? The cross-sectional area…

A:

Q: A wire of length 2m and cross sectional area 104 m² is stretched by a load 102kg the steel wire is…

A: We have to compute here,(a) Longitudinal stress(b) Longitudinal strain(c) Young's modulusWe have…

Q: 1. A homogeneous 800 kg bar AB is supported at either end by a cable as shown in the figure. Bronze…

A:

Q: Explain about Tensile and Compressive Stress and Strain.

A:

Q: If the deformation produced in 20 mm length rod is 0.085 mm, the strain is equal to: Select one: a.…

A: (d) 0.00425

Q: A cylinderical steel rod with of a meters is Subjected to a 100 x 109 Pa stress. The Young's modulus…

A:

Q: Each section of the sky way is 1.7 km long, and each segment has a cross-sectional area of 117.4 m2.…

A: In this case, the length of each section of the skyway is given. And each has some cross-sectional…

Q: coefficient of viscosity is equal to the ratio of shear stress to shear strain. True or False? a)…

A: True or False: Coefficient of viscosity is equal to the ratio of shear stress to shear strain.

Q: The dimensions of the Tensile Stress is Select one: O a. MLT-1 O b. ML2T-2 O c. MLT-2 O d. ML-1T-2 O…

A:

Q: A cast iron rod of diameter 18 mm and length of 240 mm is subjected to a tensile load of 100 kN, and…

A: Given. T = 100KN = 100,000 N D = 18mm = 0.018 m L = 240mm = 0.24m ∆L = 0.0006 m

Q: Block A is held in equilibrium when force F = 140 lbf is applied. Each cable is made out of 5-0s…

A:

Q: Find the modulus of elasticity of a brass rod of cross section 20 mm x 20 mm, and length 248 mm…

A: Tensile load(T)= 50 KN Elongation (e)= 0.25 mm = 2.5× 10-⁴ m Length of the rod(L)= 248 mm= 0.248 m…

Q: You are designing a small bridge. Find the minimum diameter of a cable with a tensile strength of…

A: Given data The tensile strength is given as σ=75 MPA. The support load is given as F = 15 kN.…

Q: Find the internal load of each section of the bar due to the loading shown. Alsofind the maximum…

A: Solution:-Given thatthickness of the bar (t)=0.5 in

Q: An aluminum bar AD has a cross sectional area of .40in^2 and is loaded by forces P_1=1700lb,…

A: This can be done using difference of forces

Q: A 195-kg load is hung on a wire of length of 3.80 m, cross-sectional area 2.00  10-5 m2, and Young's…

A: According to stress by strain relation , stress is defined as the product of Young's modulus to the…